20 Most Recent Creda IWD12 Front Load Washer / Dryer Questions & Answers

0helpful
1answer

Creda iwd12 - how to remove the front

Its very simple to do when you fit them daily but first time is very difficult
2/2/2018 7:13:09 PM • Creda IWD12... • Answered on Feb 02, 2018
0helpful
3answers

There is a permanent smell which taints the clothes. How do I get rid of it

is it a front loader? Do you keep the door to the washer closed? You may need to sanitize the door gasket as well as the drum
1/3/2015 12:56:20 PM • Creda IWD12... • Answered on Jan 03, 2015
0helpful
1answer

Creda Tumble Dryer with slow tumble action

check the capacitor motor
3/7/2014 12:31:38 AM • Creda IWD12... • Answered on Mar 07, 2014
0helpful
1answer

Condenser dryer

PULL OUT THE PLUG on the bottom right on the back is the water pump it needs cleaning or replacing not lifting the water to the water draw
2/11/2014 10:06:43 AM • Creda IWD12... • Answered on Feb 11, 2014
0helpful
2answers

My creda reverseair tumberledryer won';t work. my

Hi

If you can hear the motor running and have also checked the belt tension and they are O.K., then the only thing I can think of is the Motor pulley, where the belt sits on.

Check that out and make sure it is not loose on the motor shaft, so that the motor turns but the pulley slips.

Regards
Ash
10/31/2013 2:53:45 PM • Creda IWD12... • Answered on Oct 31, 2013
0answers
0helpful
1answer

Creda dryer kicks out breaker

could be one of the thermostats thats at fault, ,,
9/10/2013 11:27:38 AM • Creda IWD12... • Answered on Sep 10, 2013
0helpful
3answers

A Creda condenser dryer TCR2, it went off won't work at all now

There is a lint filter inside the front of the m/c.
A filter at the bottom left of m/c,undo catches to release it, remove it and wash out under running water to thoroghly cleanit.
.Remove water container at top left front , and empty.
Make sure air intake and air out lets are clear, one at front right, and one at rear of m/c.
You can download user instructions.
Goto;;
www.hotpoint.co.uk

Click on (after sales), click on download user instructions, and follow the guide

Plz rate my solution.
Thanks.
1/19/2012 1:07:12 PM • Creda IWD12... • Answered on Jan 19, 2012
0helpful
1answer

Service manual fora creda tcr2 tumble dryer

Hi from retired Englishman in SW France,

I'm so sorry but this forum does not, nor is in a position to, supply any type of manual (service or otherwise), parts list, installation instructions, electrical or schematic diagrams direct; it's just made up of ordinary guys and gals, probably at home and from all over the world, with experience of addressing problems and giving guidance for free on the web ;-0)
Also members on Fixya are not 'affiliated' to, or representative of, any manufacturer at all, just using their experience gained probably over many years.

Manual
You will need to type into your search engine/web browser '(make model number) washer service manual' and you may be presented with a number of sources from which you can either download for free or have to pay a nominal amount.
You could also try the manufacturer's web site direct but often it will supply only to registered agents.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C.
10/9/2011 12:26:52 PM • Creda IWD12... • Answered on Oct 09, 2011
0helpful
2answers

My washing is stuck in the machine, the door wont

Hi from retired Englishman in SW France,

I would gently suggest as a first step that you clean the drain motor/pump lint tray/filter. So many 'faults' are caused by blocked filters and many machines will not even go to rinse or spin or release the door lock if there is any water still left inside.
Following are my complete and generic guidance notes for checking both the drain motor filter and the drain motor ;-0)

REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT (alternatively use a wet vac as sensibly suggested by VinnyB1234!)
If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!). These panels are either held on by (plasic) screws or will just pull off. Most filters are held in by a round cover/knob. Sometimes the filter will not come out with the cover and you will have to persuade it to come out to play.
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C
8/15/2011 4:06:49 AM • Creda IWD12... • Answered on Aug 15, 2011
0answers
0helpful
1answer

Smells like old smelly socks

this might be coming from the rubber door seal clean it all the way round make sure holes at bottom are not blocked and the rubber door seal is all clean. also clean the draw so there is no power left in there and it is all clean. also a good thing to do is run it though a cleaning cycle with normal detergent at max temperature that the machine can do. hope this helps.
9/20/2010 8:04:10 PM • Creda IWD12... • Answered on Sep 20, 2010
0helpful
1answer

I am unable to open the door of my Creda washing

Unplug it for 30 mins then try again
1/15/2010 11:24:47 PM • Creda IWD12... • Answered on Jan 15, 2010
0helpful
1answer

Programme selector keeps spinning

sounds like the timer is faulty and needs replacing
10/19/2009 11:53:31 AM • Creda IWD12... • Answered on Oct 19, 2009
0helpful
1answer

Creda dryer belt

release tentsion from belt pulley
6/6/2009 6:19:48 PM • Creda IWD12... • Answered on Jun 06, 2009
0helpful
2answers

Dial keeps turning and clicking

sue worth having inlet valve checked also have heater checked at same time ! is the machine draining ok !! if not there could be blockage in drain system or faulty pump good luck- regards bob btw
4/4/2009 1:55:49 PM • Creda IWD12... • Answered on Apr 04, 2009
0helpful
1answer

How do i get to the drum to put new belt on

there is a pulley wheel at the rear of the machine that the belt goes between this and the motor shaft, you do not have to get to the drum at all. you will however need to get the machine out to get to the rear of it, there should be an access panel at the rear which will let you put the belt on. remember to disconnect all water and electricity before removing the machine. put the belt on the motor first and then run round the pulley wheel by holding it to the wheel and rotate on, be careful the belt will be taught when applied so watch your fingers do not get trapped.
3/28/2009 12:27:48 PM • Creda IWD12... • Answered on Mar 28, 2009
Not finding what you are looking for?
Creda IWD12 Front Load Washer / Dryer Logo

47 questions posted

Ask a Question

Usually answered in minutes!

Top Creda Washing Machines Experts

matt
matt

Level 3 Expert

1661 Answers

john h

Level 3 Expert

27542 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

49959 Answers

Are you a Creda Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Creda Washing Machines

  • Creda Washing Machines

Most Popular Question

service manual fora creda tcr2 tumble

  • Washing Machines
Loading...