20 Most Recent Seiki 32" LED TV - SE321FB - Page 2 Questions & Answers

Hi, the standard advice on FPtvs is to remove all attached devices and reset the tv to factory default. If the problem is still experienced you will then know that it is a hardware fault. In your case the reset may correct the issue but if it does not I will state the obvious, (sorry,) the sound output section has gone.This may be motherboard related. Also see below link for possible remedies if you do not want to reset to default https://answers.yahoo.com/question/index?qid=20080217074818AA5aEgG

Practical Guide to Calibrating Your TV

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the relative post easily. http://remotesearch.blogspot.com/ http://electronicshelponline.blogspot.com/ http://electrohelponline.blogspot.com/

You should have a remote control to select its inputs. If you wish to buy its original remote control, contact the authorized service centre, or authorized dealer to your device brand. They can either give you a genuine remote control to your device, or can direct you, from where can you purchase a suitable one. To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. Both the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability. Brand name of the remote control isn't a matter, but it should have set-up codes in its code list, to the device brand you have. Please note: Every new universal remote control will have set-up code list, and set-up procedure along with its pack. Never accept a remote control, that hasn't both of this. For more details about the set-up codes, visit the site http://electrohelponline.blogspot.com/ Check this site too. http://remotesearch.blogspot.com/ Universal remote controls are available at most of the electronic spare part selling shops. Type in the "brand name only" of your device, in the search box [at the top right] of the display window and the Search will start at once as you type in, and will show you all the related posts. It will make surf easy.

hi you could have put it in the wrong way accident, try putting another one in it should eject, good luck regards shaun

Depending on your model you might need a update in the firmwar v?rifiy on the constructor web site http://www.seiki.com/support/downloads.php

hi first make the mute button hasn't pressed if ok try plugging earphones in if you hear sound then audio ic is working, you need to test the speaker, with a multimeter thanks shaun

NO sound at all I tried the mute button and still no sound

Cannot be done. The USB port on the TV is for "Service use only", according to the TV's specs on the manufacturer's Web site. SEIKI SE321FB

Are you connecting to another device for reception, cable, dvd plyer?

You can check Ebay, but for the price that 32" TV's are going for it is hardly worth the time to do that. Just go buy a new one and avoid what cracked the first one.

Your TV must receive a digital signal in order for the DTV option to be available. Since you are not seeing all of the channels when you auto scan then it can be assumed that the signal cable connected to your set is not providing the digital signal. Make sure you are scanning for the proper source of your signal ( Cable TV, Broadcast TV)

That part is soldered into the TV circuitry. Chances are that a TV repair professional will need to open it up unless you know someone that knows how to desolate and solder in a new plug. If the circuit board is damaged, then you will have to source a new part.

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ Line, faults & possible causes to LCD screen are given with illustrations.

Try a hard reset to this set, and check. Just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. This must make it a hard reset. Try after that. It it does not help you, the main system control memory IC to the set is faulty, and should be replaced. Contact any service technician. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" or "Magazine" will make surf easy. Pull up older posts. Surf the site with patience. Do a search by type in the brand name of your device at its search box. http://electronicshelponline.blogspot.com/

If they are blurry lines, likely you have a problem with heat damaging the diffuser plate behind the LCD. Unfortunately, there is no fix to this other than to replace the screen, which is as much as the same TV used. It's usually caused from the vents in the back of the tv getting clogged with dust/debris/smoke and the power inverter overheats. It causes the screen to develop a line on one side of the screen, then it starts to look like the screen was washed with something and you get black streaks running from the top which usually is accompanied by a darkened blurry "cloud".

The back light lamp has most likely gone out on this. If you pull it apart you can find a replacement part and put it in yourself.