20 Most Recent Epson Stylus Photo 785EPX InkJet Printer Questions & Answers

Software is here: http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?BV_UseBVCookie=yes&oid=14365&prodoid=1567218&infoType=Downloads&platform=All
Here's just the Windows software: http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?oid=14365&prodoid=1567218&BV_UseBVCookie=yes&infoType=Downloads&platform=Windows&x=16&y=14
Good Luck.

Reset your Printer by following these steps for your Printer Model:

EPSON Stylus Color 900, 980
Pressing and holding LOAD/EJECT and CLEANING buttons, press POWER button, You will see blinking INK OUT led.
Release all buttons.
In 2-3 seconds time press and hold CLEANING button for 10-12 seconds.
EPSON Stylus Color 3000
Pressing and holding PAUSE, LF/FF and DOWN ARROW buttons turn on printer.
Release all buttons.
EPSON Stylus Photo 785, 895
Pressing and holding Maintenance and Roll Paper buttons, press POWER button, You will see blinking Error led.
Release all buttons.
In 2-3 seconds time until led is blinking press and hold for 10-12 seconds Roll Paper button, until all leds will blink.
EPSON Stylus Photo 890, 1280, 1290
Pressing and holding Maintenance and Roll Paper buttons, press POWER button, You will see blinking Power led.
Release all buttons.
In 2-3 seconds time until led is blinking press and hold for 10-12 seconds Roll Paper button, until all leds will blink.

www.epson.com/cgi-bin/Store/support/supDetail.jsp?infoType=Doc&oid=14365&prodoid=1567218

You have to physically clean the nozzles, rubbing alcohol and chammy covered cleaner, like vcr head cleaners.

hey cant you use the software which came along with that printer this might help you to install the driver or in windows update select the printer( most probably it will not be there and there is no alternate driver).

There is a driver--it's provided by the Microsoft website. While your computer is connected to the Internet, connect your 785EPX to your computer via USB and then turn the printer on. The driver will auto download and install. I just did this on an HP DV7 laptop and the printer works fine, showing ink levels, too, though you have to access the printer properties to see this.

Replace your paper pickup rollers.

http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?BV_UseBVCookie=yes&oid=14365&prodoid=1567218&infoType=Downloads&platform=All
first try to download the driver then install it ..after that connect the printer ...

The sponge is the head cleaner. It cleans the dried ink off the print headwhen you start a print job. If you don't replace it, your print head or cartridge will be ruined.

Go to the site link below and click on the printer icon and fil out the info it asks for. It will direct you to the drivers and software for the printer.

http://www.epson.com/cgi-bin/Store/support/SupportIndex.jsp

might be ur drivers is not installed properly so reinstall the drivers by putting cd come with ur printer or can call us at tollfree no 18884276640

After a week of frustration trying to get the blasted thing back in--I could get the roller piece back in but not with the wire and could get the wire back on the little knob that holds it but that would prevent the roller piece from going in, I cut a notch in the white plastic above the spring hole so that I could, with very small needle nose pliers, hold the straight part of the sprint up while I put the roller piece in place. I then let the spring down through the notch I cut. It took a couple of tries but it all was pretty easy once the notch was cut.

that means that the black cartridge is low on ink. Make sure to have a replacement black ready.

Hi

Please check if the cartridges are seated properly. Also check for any paper jams. If all is fine then change the usb port at the back of the pc and restart the printer. Then try and print a test page.

Windows Vista In-Box Driver Installation
Follow these steps to set up your Epson product and install the built-in Windows Vista drivers:

1. Set up your computer.



2. Connect your Epson product to your computer.



3. Follow the on-screen instructions that Windows Vista displays to guide you through product driver installation.

Question edited for clarity and add name of Maker. Question moved to correct category. Connectivity specs. Not really cordless wifi, you are connecting to the router or office network using a network cable. There would be ways around it using a powered wifi access point hub to the printer and use that to wirelessly connect to the router, but probably not cost effective. It would give you the ability to print from the Epson smartphone app. https://epson.ca/For-Work/Printers/Large-Format/Epson-Stylus-Pro-4900-Printer/p/SP4900HDR Superior Connectivity

• Standard ports include one high speed USB 2.0 and one 10/100 BaseT Ethernet
• Standard professional Epson Photographic Drivers for Macintosh® and Windows®
• Fully supported by most leading third party RIPs and workflows

Support, Manuals and Network Connection Guides. https://epson.ca/Support/Printers/Single-Function-Inkjet-Printers/Epson-Stylus-Series/Epson-Stylus-Pro-4900/s/SPT_SP4900HDR#manuals And this is the document.

Epson Stylus® Pro 4900 - Network Guide

Epson https://files.support.epson.com > pdf > pro49_ng 1. Click Start, select Control Panel, and then select Network Connections. 2. Under LAN or High-Speed Internet, right-click the Local ... 39 pages ..

The error E-91 on an Epson Stylus RX 520 indicates a communication problem between the printer and the cartridge. Here are some steps you can try to resolve the issue:

1. Turn off the printer and unplug it from the power source.
2. Remove all the ink cartridges and check for any damage or leaks. Replace any damaged or leaking cartridges.
3. Clean the metal contacts on the ink cartridges and inside the printer with a soft, lint-free cloth. Make sure they are completely dry before reinserting the cartridges.
4. Reinstall the ink cartridges and make sure they are properly seated.
5. Turn on the printer and see if the error message still appears.

If the error message persists, try resetting the printer by following these steps:

1. Turn off the printer and unplug it from the power source.
2. Hold down the "Stop" and "B&W" buttons while plugging in the power cord.
3. Keep holding the buttons until the printer starts to initialize.
4. Release the buttons and wait for the printer to finish initializing.
5. Try printing again to see if the error message is resolved.

If none of these steps work, there may be a hardware issue with the printer and it may need to be serviced by a professional technician.