Top 20 Frymaster Dean FM345EETC Deep Fryer Questions & Answers


The gas valve may be leaking gas out where it should not be leaking gas out. You may need a new gas valve. This could be a safety issue, not just with a fire, but a potential fire gas explosion. Please get it fixed ASAP.

Frymaster Dean... • 140 views • 0 helpful votes


Hi,
There is a problem in the system. The problem is usually a sensor that is not reading correctly or not working right.
To troubleshoot this type of problem it is best to call the factory tech. support people and have them walk you through the troubleshooting. then they can also guide you to getting the proper replacement parts. For a problem that is showing up like that you will need OEM parts anyway.

heatman101

Frymaster Dean... • 200 views • 0 helpful votes


You have a lazy thermostat that needs replacing. Not uncommon.


Tom

Frymaster Dean... • 267 views • 0 helpful votes


first thing I would check is to make sure the quick disconect on the gas hose is fully connected,and that the cut off valve is tured on.Sometimes the orifice in the pikot assembly can become stopped up.(where you light it by the burner)you can check there by undoing the gas line at the compression nut on the assembly.the hole is really small and you can use a small needle to clear it.

Frymaster Dean... • 1,741 views • 2 helpful votes


Ok sounds like your problem maybe that the gas valve is set to low. If you have access to a manometer you can put it on the outflow port of the gas valve and see what the reading is. It should be at 4" water column for this fryer. You possibly might even have a faulty gas valve, these will go out sometimes and still let the pilot bypass maintain regular operation. Please comment me back if you need more assistance with this.

Thanks

Frymaster Dean... • 207 views • 0 helpful votes


Check your transformer and make sure that it is tapped for 110v

Frymaster Dean... • 155 views • 0 helpful votes


Here's a link that may help,find your model and click on it,k. http://www.frymaster.com/minisite/service/manuals

Frymaster Dean... • 167 views • 0 helpful votes


This might be due to a loose wire in the light that or it is going out.

Frymaster Dean... • 75 views • 0 helpful votes


The burner or the burner venturi is clogged. The burners are held in place with 2 bolts at the top and you need a 1/2 inch wrench. Remove the bolts and lift the burners off the brass orifices. Make sure all the holes are clear. If they are clogged they need to be drilled out. You should not have yellow in the flames in the burner tube.... kinda looks like the are sooting. This causes flames to come out the bottom of the burners.

Frymaster Dean... • 93 views • 0 helpful votes


There is an adjustment screw on the main gas valve, usually under a cover screw. It will be near where the small pipe that goes to the pilot light.

Frymaster Dean... • 155 views • 0 helpful votes


One time this happened to me on a gas stove. I used an electric drill with drill bit to clean it out. It will only work if the line is straight, no bends in the line.

Frymaster Dean... • 115 views • 0 helpful votes


Defective thermocouple. It is the metal tube that is in the flame of the pilot light.

Frymaster Dean... • 380 views • 0 helpful votes


venting is bad ---- soot build up - obstructions---------clean your unit

Frymaster Dean... • 70 views • 0 helpful votes


Hi there. Hi limit may be tripping off due to high oil temperature (power supplying the gas valve is connected in series with the hi limit). Verify if the thermostat is not shorted, also please check the thermostat calibration if it is good. Regards.

Frymaster Dean... • 231 views • 0 helpful votes


I need to replace it

Frymaster Dean... • 51 views • 0 helpful votes


Likely one of two things. The thermostat is stuck on or your gas valve is bad. Identify one of the wires going to the thermostat and disconnect it, if the burners shut off with the thermostat disconnected the problem is the thermostat, otherwise it will be the gas valve. All this assumes the unit is wired correctly and has not been changed. If your burners are not shutting off due to a bad gas valve or thermostat you are at risk to have a fire! Be sure to get this fixed immediately and it is unsafe to operate the fryer until repaired.

Frymaster Dean... • 541 views • 1 helpful votes


Hi there!Check the hi-limit by removing the wire at terminals and connecting an ohm-meter across, it should have continiuty, if it does not have, better replace it with a new one.Regards.

Frymaster Dean... • 135 views • 0 helpful votes

Not finding what you are looking for?
Frymaster Dean FM345EETC Deep Fryer Logo

8 questions posted

Ask a Question

Usually answered in minutes!

Top Frymaster Dean Kitchen Appliances - Others Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Paul Carew

Level 3 Expert

3538 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Are you a Frymaster Dean Kitchen Appliances - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Frymaster Dean Kitchen Appliances - Others

  • Frymaster Dean Kitchen Appliances - Others

Most Popular Question

frymaster pilot not lighting

  • Kitchen Appliances - Others
Loading...