20 Most Recent Indesit WA 115 Front Load Washer - Page 5 Questions & Answers

Sounds like it needs a new timer. The timer is the brain and tells the machine what to to.

There are shops in Dubai which could help you. And lots of Philipinos in Dubai - they could surely help.(!) Wil try to get you an email of a shop.

First check whether your inlet valve is open on the wall; if that is not the problem check to see that the inlet valves are not clogged with some dirt or something, clean out and refit. Plug off the wall and careful with the water spillage. The final part should be to check whether the water flows into the machine, ie. the entry at the soap dispenser. Simple.

indesits dont have carbon brushes they have a module which controls everything to your tomer if this is faulty or your timer then its not worth doing too much in money to replace get a hoover or candy same machine just ones the uk model and the other is the us model dont go for hotpoint though because indesit own hotpoint now and there changing the carbon brushes to modules which is a big mistake alot dearer to replace then the carbon brushes but maybe thats why there doing so customers have to buy another washer check the price by going to indesit customer support web site but i always keep customers away from indesit due to that module some hotpoints are still the carbons but some arent cheaper to buy a slight damaged from a washer repay shop they usually have damaged at a fraction of the price save at least £125 per washer or buy a repossed one may off been used at the most 10 times nothing wrong with them and you will save £200 plus m8

common for the impellor to come off the drain pump also common to have water in the pump rotor housing making the pump fail to start

poss moisture on your control module causing tracking . unplug your machine from the mains and take the back panel off, you can try blowdrying the module down in the bottom left hand corner or you can take it off (noting where all the leads go to),get an old toothbrush and clean the solered side around the bottom of the board failing that you will most probably have to change it

this indicates a fault unfortunenately it doesnt say which one the most likely problem will be brushes in your motor

probable cause is just poor water flow from outside. switch water off. undo hoses and check not kinked. in each hose, there should be a gauze filter. clean this. look inside the valve spigot and check no dirt buid-up. put hoses in a bucket and check water flow is ok. remove drawer and check holes in top of box are clear

Hi - had a similar problem with about 3 different makes of washing machine - the RCD switch on the main household fuse box was continually tripping . Nobody could give me a right answer . Eventually ended up with a Hotpoint . Felt sorry for the delivery guys from the electrical retailers having to keep dragging machines in and out .

I have the same issue, have just returned from a 9 month break and now the washer does the click thing, but if you open and close the door a few times and set to program 4 is seems to work after about 10 minutes! It was perfect when I left, not 18 months old either. Can see it being the timer either, maybe a pickup of some type not detecting a level? Peter

sounds like a pump problem. see if theres a broken belt going to the pump. if its a direct drive unit then the clutch solinoid could be defective or the timer as well. What you need to do is if its a direct drive is measure the voltage on the solinoid or switch wehn its supose to dran if its there then the switch or solinoid is bad. If its not there then most likly the timer but I would need to see the wiring chart to be sure. good luck PS the wiring chart is inside on the back or on one of the sides in most washers and dryers.

If your Indesit IWDD7143 washing machine is trying to operate the inlet valve during the dry cycle, there could be a few potential reasons for this issue:

See page 28 troubleshooting of user manual Troubleshooting - Indesit DFG 15B1 Operating Instructions Manual [Page 28] ' ManualsLib Here is service manual for help INDESIT DFG151SIT Service Manual download, schematics, eeprom, repair info for electronics experts (elektrotanya.com) See this video for further help https://www.youtube.com/watch?v=TzQ1hNJnHR8

I would check the water inlet flow rate is fast enough as these will time out if they can't get enough water fast enough.

If your Indesit XWA91683 washing machine fills with water but does not start the wash cycle, and you have confirmed that the pump is working fine, there could be a few potential causes for the issue, including a malfunctioning motherboard. Here are a few steps you can take to troubleshoot the problem:

1. Power Cycle: Start by turning off the washing machine and unplugging it from the power source. Wait for a few minutes, then plug it back in and turn it on again. This can help reset the machine's internal settings and may resolve temporary issues.
2. Check Door Interlock: Ensure that the washing machine's door is securely closed and the door interlock mechanism is functioning properly. A faulty door interlock can prevent the machine from starting the wash cycle. Check for any loose connections, damage, or obstructions in the door interlock mechanism.
3. Reset the Control Panel: Depending on the model, your washing machine may have a combination of buttons or a specific sequence to reset the control panel. Consult the user manual for your Indesit XWA91683 or contact Indesit customer support for instructions on how to reset the control panel to factory settings.
4. Examine the Control Board: If the above steps do not resolve the issue, there could be a problem with the motherboard or control board of the washing machine. Inspect the control board for any visible signs of damage, such as burnt components, loose connections, or corrosion. If you notice any significant issues, it may be necessary to replace the control board. Consult a professional technician or contact Indesit customer support for further assistance.

It's worth noting that diagnosing and repairing issues with the motherboard or control board typically require professional expertise. If you are not confident in handling these repairs yourself, it is recommended to consult a qualified technician or contact Indesit customer support for assistance. They will have the knowledge and tools to accurately diagnose the problem and provide appropriate solutions.

Follow these procedures to remove the back access cover on an Indesit WIE 167 washing machine and replace the belt: Disconnect the washer from the electrical outlet and turn off the water supply. Move the washing machine away from the wall so that the back can be accessed. Find the screws that secure the rear access cover. Often, they are positioned throughout the cover's perimeter. Remove the screws using a screwdriver and store them in a secure location. Carefully remove the washing machine's back access cover. Using a flat instrument, such as a putty knife or a scraper, to pull the cover away from the machine may be useful. Once the cover is removed, the belt should be accessible. Remove the old belt from the machine with care. Put the replacement belt on both the motor and drum pulleys. Align the back access panel with the washing machine and secure the screws to reattach it. Reconnect the washing machine and activate the water supply. Verify that the replacement belt works properly by putting the washing machine through a series of tests. When servicing a washing machine, it is essential to observe all safety precautions. If you are uncertain or uncomfortable with any of these processes, it may be better to call a skilled technician or service center for assistance.

If the drum of your Indesit IWC5085 washing machine is jammed, there are a number of methods you can try to take to address the problem: Look for tiny objects: Look for tiny objects that could be lodged in the drum, such as coins or buttons. They may result in the drum becoming blocked and impair its ability to spin. Inspect the filter: Look inside the washing machine's bottom-mounted filter for any particles or anything that might be the obstruction. Remove the kick plate from the washing machine's bottom to gain access to the filter. Inspect the pump: Look for any obstructions or blockages in the washing machine's bottom-mounted pump. Remove the kick plate from the washing machine's bottom to gain access to the pump. If there is a clog, remove it with care before attempting to restart the washing machine. If the drum isn't spinning at all, check the belt. It could be loose or broken. Unplug the washing machine and take off the back panel to inspect the belt. Check the belt for any indications of wear or damage. The belt must be replaced if it is damaged or loose. It could be required to seek the aid of a qualified repair technician if none of these measures succeed in fixing the problem.

F09 - Setup error
Book a washing machine repair

it seems like the issue is not resolved even after replacing the pump. It could be related to a problem with the control board or a faulty water level sensor. You may want to consult a professional repair service