20 Most Recent Sony Cyber-Shot DSC-H1 Digital Camera - Page 2 Questions & Answers

select menu->settings-> then you can see reset the factory settings

You can get a good used LCD pulled from a camera online for about $40 to install yourself. I don't get paid by that big auction website, so I don't type their name, sorry.

Thomas

Fixing a Lens Error on a Digital Camera

This has to be THE most common failure mode for a digital camera. Some common error messages that might show up on the LCD's of cameras with this problem include "E18 lens error", or "lens error, restart camera". Some cameras might show nothing at all, but merely make a beeping noise as the lens goes out, then in, then the camera shuts off. Sometimes the lens won't even move.

The problem is actually quite common throughout all camera brands. Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. Believe it or not, one BIG contributor to lens errors is using a camera case. Sand, gunk, case fibers, etc... accumulate at the bottom of the case. These materials love to cling to the camera by electrostatic build-up from the camera rubbing against the side of the case (especially those cases with soft fibrous interiors). Once these materials work their way into the lens mechanism, that's all she wrote. I have many cameras, and NEVER use a case for this very reason.

A camera owner that suffers this problem may have no recourse for having the camera repaired. Many camera makers will not honor repairing this problem under warranty as they claim it is due to impact damage to the camera, or sand or debris getting into the lens gearing mechanism (neither of which is covered under warranty). The quoted repair cost is usually close to or more than what the camera is actually worth.

Fortunately, about half the cameras that suffer this failure can easily be fixed by one of the following methods. None of these methods involve opening the camera, although some have potential to cause other damage to the camera if excessively done. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.

The methods are listed in the order of risk of damaging your camera. Thus make sure you try them in the listed order. And remember, these fixes (especially #6 and 7) should only be considered for a camera that's out of warranty, who's cost of repair would be excessive, and would otherwise be considered for disposal if unrepaired:

Fix #1: Remove the batteries from the camera, wait a few minutes. Put a fresh set of batteries back in (preferably rechargeable NiMH 2500mah or better) and turn the camera on. If that didn't work, try pressing and holding the Function or OK button while turning the camera on.

Fix #2: Remove the batteries, then remove the memory card. Then install new batteries, and turn on the camera. If you get an Error E30, it means you don't have a memory card installed, so turn it off, slip in the memory card and turn it on one last time.

Fix #3: Insert the cameras Audio/Video (AV) cable, and turn the camera on. Inserting this cable ensures that the camera's LCD screen remains off during the start process. Thus extra battery power is available to the camera's lens motor during startup. This extra power can be useful in overcoming grit or sand particles that may be jamming the lens. If the AV cable doesn't fix the lens error by itself, consider keeping this cable installed while trying fixes 4, 5, and 7 as a means to provide extra help to these fixes. But note that I DON'T recommend keeping the cable installed during Fix 6 as you may damage the AV port while tapping the camera. Reinsert the cable only AFTER tapping the camera.

Fix #4: Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to autofocus while the lens is extending, hopefully seating the lens barrel guide pins in their slots.

Fix #5: Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in "no heat" setting, or sucking the gaps with a vacuum (careful with this one).

Now we're entering into the realm of potentially damaging your camera in conducting the fix. There is definitely some risk here, so take care when conducting the following two fixes.

Fix #6: Repeatedly tap the padded/rubber usb cover on a hard surface with the intent of dislodging any particles that may be jamming the lens. Other variations include hitting a side of the camera against the palm of your hand. A lot of people have reported success with this method. HOWEVER, there is also some potential for damaging or dislodging internal components with this method, such as unseating ribbon cables, or cracking LCD screens.

Fix #7: Try forcing the lens. More people have reported success with this method than with any of the other methods. HOWEVER, there's obviously some potential for damaging your camera by using this method. Variations include gently pulling, rotating, and/or twisting the lens barrel while hitting the power button. Attempt to gently straighten or align the barrel if it's crooked or twisted. Another variation includes looking for uneven gaps around the lens barrel, and then pushing on the side of the lens barrel that has the largest gap (note pushing the lens barrel all the way in is NOT recommended as it may become stuck there). While doing any of the above, listen for a click that indicates that the lens barrel guide pins may have reseated in their guide slots. If you hear this click, immediately stop and try the camera.

Hi,
Clean battery terminals of battery compartment of camera and make sure terminals are clean and shiny, and check.
Thanks.

you can buy here:
http://cgi.ebay.com/SLAVE-FLASH-SONY-CYBERSHOT-DSC-H1-DIGITAL-CAMERA-/120604081156?pt=Digital_Camera_Flashes&hash=item1c14903c04
Thanks for using fixya.

hi if you can not access in order to get picture out memory stick, then take easy way. you just get a usb external memory card reader and connect to computer. your computer now will recognize as a diver. then you put memory stick into the slot. open my computer and you will see your picture drive and folder. now you can handle whatever you want. you may use built in memory card reader, too. if you have. thanks and best regard!

It's in the Shooting menu, under "PFX" (pages 38 and 41 in my copy). If you need a manual, you can download one from
http://esupport.sony.com/US/perl/model-documents.pl?mdl=DSCH1

On the side of the camera there's a plastic flap, if you open that up you'll see the USB port where you can connect a USB cable.

I guess, you enabled the BRK mode that takes up to 16 Pictures. There's a button on the top of the camera to turn that on/off.

Consider NOT connecting your camera to your computer.

The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB or FireWire). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries.

Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use any photo cataloging program.

The truth is, you cannot do this repair yourself. You don't have the tools or the expertise in soldering small parts necessary. Sorry.

If you are shooting with flash and using alkaline batteries, this certainly could be the case. If you are using lithium batteries or NiMH rechargeable batteries and are not shooting with flash, and are having this problem, then there is likely some internal problem with the camera that is draining the batteries unnecessarily.
In that case, you'd want to take the camera to a repair shop for troubleshooting.

Use a tooth pick to fire the shutter temporarily until you can get the part - the button needs to be replaced. Insert a pointed object into the hole and it will shot when the shutter switch, which is a push button, is pressed. I think there are repair shops there who can fix the switch or button than using a tooth pick, that's better.

hi there

You will be able to replace the shutter button alone to resolve the issue. It is not required to replace the whole body. You can contact sony direct accessories and Parts Center to get the replacement shutter button.
If you require assistance with contact number to reach the accessories shop, you can ask me by clicking following link:
fixya.com/users/shajanrs

Hi there you need to open the camera casing then you can remove the flash light. But if you want to do this at home you need to know chip level circuit board repairing. ask me if any thing else.

Sorry but, your camera is busted.

http://esupport.sony.com/US/perl/model-documents.pl?mdl=DSCH1

There are a number of manuals for the 2005 model year camera.
I have one and am very satisfied with it.

Solution
Cyber-shot cameras nowadays have a built-in rechargeable battery for retaining time, date, and other settings. Since the built-in rechargeable battery is not removable, current Cyber-shot camera models can only be returned to the original factory settings by pressing a small RESET button on the camera or by using an Initialize option in the menu.
Older-model Cyber-shot cameras (prior to the year 2000) do not have a built-in rechargeable battery and do not have a RESET button or Initialize option in the menu. These cameras require a manual power reset.
IMPORTANT: To determine whether or not your camera has a RESET button or Initialize option, or for other model-specific information to complete any of the steps in this solution, refer to the operating instructions supplied with the product. Manuals are available online through the Manuals/Specs/Warranty link on this page.
Follow the appropriate procedure below for your camera.
Using an Initialize option in the menu
Since Cyber-shot cameras have different menu system layouts, refer to the instruction manual specific for your camera model.
Using a RESET button

1. Locate the RESET button on the camera.
2. Use a pointed object (like a ballpoint pen) to press and hold the RESET button for 2-3 seconds.
3. After 2-3 seconds has elapsed, release the RESET button.

Performing a manual power reset

1. Turn off the camera.
2. Remove the battery pack.
3. Remove the button-sized lithium battery.
4. Allow the camera to remain without power for 30 seconds.
5. Reinsert the button-sized lithium battery.
6. Reinsert the battery pack.
7. Turn on the camera.

If your camera is experiencing an issue and the issue is not resolved by performing the appropriate reset procedure above, then service may be required. Click the Repair & Status link on this page for available service options.
---
https://eservice.sony.com/webrma/web/index.do