Inland 87093 Supra-aural Proht Bluetooth Headset black - Page 5 - Answered Questions & Fixed issues

Both devices' B.T. = on.
Device A = "Search for devices"
A finds B...
Select Device B to pair with.
On B accept pairing with device A.
May ask for BT passwords, try 0000 as default.

Radio... | Answered on Jun 22, 2019 | 133 views

Try a reset. Hold down the power button for >15 seconds.

Radio... | Answered on Jun 15, 2019 | 132 views

time for an aftermarket replacement then. that's your best and cheapest step. you might check they usually have some really good prices on stereos there.

Radio... | Answered on Jun 15, 2019 | 131 views

on what? you are giving the error but no details about the problem if it's in your car, on your computer, on your phone or what. we need DETAILS and the more the better. we can't help you properly if we have no clue what it is you're talking about even.

Radio... | Answered on Jun 14, 2019 | 148 views

Please see below. I believe that you have set the tuning to LOCK, hence the KEY symbol. I have done the same thing with other radios. I bet you never forget this!

Manual Tuning with Rotary Dial You can select a higher or lower frequency by turning ROTARY TUNING. Set FAST/FINE/LOCK to select the rotary tuning increments or to lock the ROTARY TUNING dial. The following table shows the tuning increments for the FAST and FINE settings. '------'------'-------'------'-------' ' ' FM ' LW ' MW ' SW ' '------'------'-------'------'-------' ' FAST ' 0.1 ' 9 kHz ' 9/10 ' 0.005 ' ' ' MHz ' ' kHz ' MHz ' '------'------'-------'------'-------' ' FINE ' 0.05 ' 1 kHz ' 1 kHz' 0.001 ' ' ' MHz ' ' ' MHz ' '------'------'-------'------'-------' To lock the ROTARY TUNING dial, set FAST/FINE/LOCK to lock. This keeps you from changing the frequency if you accidentally touch the dial. NOTE: This locks only the ROTARY TUNING dial.

Radio... | Answered on Jun 13, 2019 | 153 views

As a technician, I would think it’s more than likely a parent problem or it could be a battery dead on one of the devices and it cannot see it or there’s too many things generating that particular frequency in that area. Good luck

Radio... | Answered on Jun 13, 2019 | 150 views

very simple you should be able to tell by sound, have someone else talk into mic while you go the audience. I hope you are using a good quality mic and American cables with Nutrek connectors. If you have a mic and cable together I would replace it. You will need to hours studying mic patterns to determine which pattern you will need. I would us a cardiod pattern not an omni pattern. If you are putting your mouth on or too close the sound will be terrible. Practice your enunciation.

Radio... | Answered on Jun 10, 2019 | 130 views

Use the AUX jack, the old cigarette lighter jack to get a 12V feed. It will work fine as long as you are not using a linear amplifier with the radio.

Radio... | Answered on Jun 09, 2019 | 157 views

Ham radio fests, Craigs list, local ham club. Maybe a CERT type of group (citizens emergency response team). We have those and they use ham radios. Also try emergency services in your county. You will never get what you paid....Used Ham gear goes cheap.

Radio... | Answered on Jun 05, 2019 | 345 views

Hi. Google has the user manual at: blob:

The info you are looking for is in section 4. Basically you press the shift key to do want you want.

Good Luck.

Radio... | Answered on Jun 04, 2019 | 146 views

I think you will find the problem is in one of the microphone wires. The switch for TX/RX is in the mic, and if the RX wire opens up, you will not get any receive audio.

Radio... | Answered on Jun 04, 2019 | 171 views


please try to hard reset both units,
be sure its charged


Radio... | Answered on Jun 03, 2019 | 129 views

need get battery our and spry CRC Cleaner to Battery contact cause they are rusted

Radio... | Answered on May 30, 2019 | 185 views

You would have a better chance of someone being able to help you if you post of the make and model of the radio. Base, mobile etc.

Radio... | Answered on May 25, 2019 | 168 views

Hello Jeff, I was looking for the user manual of your CB Radio Hatadi, to know what fuse it takes and there is no information
I would try the 5 Amp, I would place it and it would work for a long time to the BC Radio, checking that the fuse resists the transmission work
If it does not resist, I would put the 10 Amp and would do the same test
If it does not resist either, then you already have problems with the equipment
If so, look for a specialized technical service
I hope you can solve the problem
Greetings Franco Dosil
Hola Jeff, estuve buscando el manual de usuario de tu CB Radio Hatadi, para saber que fusible lleva y no hay informacion
Yo probar?a con el de 5 Amp, lo colocar?a y har?a funcionar por un rato largo al BC Radio, comprobando que el fusible resista el trabajo de trasmisi?n
Si no resiste, pondr?a el de 10 Amp y har?a la misma prueba
Si tampoco resiste, entonces ya tienes problemas en el equipo
Si es as? busca un servicio t?cnico especializado
Espero Puedas resolver el problema
Saludos Franco Dosil

Radio... | Answered on May 24, 2019 | 139 views

Not finding what you are looking for?
Inland 87093 Supra-aural Proht Bluetooth Headset black Logo

Popular Tags

1 questions posted

Ask a Question

Usually answered in minutes!

Top Inland Radio Communications Experts


Level 3 Expert

1658 Answers

Brad Brown

Level 3 Expert

18519 Answers

Tom Chichester

Level 3 Expert

60185 Answers

Are you an Inland Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides