Inland Pro Bluetooth Wireless Headset - Page 3 - Answered Questions & Fixed issues


Connect the headset to the charger as if you were charging it, but keep one side in your ear. Once connected to the charger, hold down the power button. It'll beep a few times and then stop. Disconnect from the charger. You can then turn the headset back on. This "procedure" clears the headset's memory,

Radio... | Answered on Oct 16, 2019 | 197 views


Radio Shack has a pretty good search feature for old instructions on their website. You will need their part number off the unit, which will be something like "20-321". Do a search and you can get a PDF instruction manual for it online.

Radio... | Answered on Oct 14, 2019 | 470 views


go to cellphones. This is radio communications

Radio... | Answered on Oct 04, 2019 | 137 views


Your antenna should not make any difference with power or receiving. Is the scanner mobile or in a room? Hard to imagine the connector being broken. You could test the antenna or even the BNC connector on the scanner. Try another antenna. If you wiggle it, does it start receiving? You may have a short in the BNC to the receiver. Other than that, look to power issues.

Radio... | Answered on Oct 04, 2019 | 133 views


Radio frequencies are different from country to country. NZ will use different frequencies than Canada. Canada and the USA have agreements in place because they border each other on what freq. is used for what. NZ likely has its own list. Your radio is not programmable to NZ frequencies. Sorry!

Radio... | Answered on Oct 23, 2019 | 134 views


It sound like your power supply is not providing enough output for the radio. Are you by chance using a wall wart for power? You need a dedicated 12 volt power supply, made by Astron, QJE, or Pyramid.

Radio... | Answered on Oct 03, 2019 | 194 views


you may have a bad squelch pot on the radio. try turning it fully in one direction an back in the other direction. it also could be that the Pot is dirty get some contact cleaner and open up the radio and squirt a very little cleaner into the open spot of the Pot. then rotate the know several times. if you do not have something like CRC QD Contact Cleaner you can get it in a good hardwood store like ACE or TrueValue, and even Home Depot. you can use only 91-99% Electronic Grade Isopropyl Alcohol, do not use the 70% Isopropyl Alcohol.

Radio... | Answered on Oct 03, 2019 | 135 views


you may have a broken wire in the radio itself? or there is a wire broken inside the mike itself not just the connector.

Radio... | Answered on Oct 03, 2019 | 149 views


you need to program the correct frequency. the Marine Channel 63A is 156.175Mhz. they also maybe using a PL Tone or a CTCSS tone, you have to find out what it is. using the Chirp Programing software you can do that. but remember sometimes a Cities use a non standard CTCSS tone so you can only hear each other

Radio... | Answered on Oct 03, 2019 | 172 views


What radio do you have? Cannot give you any answer without knowing what it is?

Radio... | Answered on Oct 03, 2019 | 135 views


What radio are you using?

Radio... | Answered on Oct 03, 2019 | 142 views


first of all what radio are you using?

Radio... | Answered on Oct 03, 2019 | 134 views


What type of radio are you talking about Ham Radio, AM & FM Radio? we need more information then this:

"Electricity went out. Unable to get radio channel of my choosing"

Radio... | Answered on Oct 03, 2019 | 118 views


try to do a Hard reset on the unit and then reload your freq list from Chirp. It happened to my UV-5R-v2 Baofeng. It worked fine after that.

Radio... | Answered on Oct 03, 2019 | 131 views


Hi,

It's a two way communications radio, not a broadcast radio, hence it won't receive FM/AM broadcast radio stations.

You should not confuse the two as they work on different radio bands, most FM broadcast radios are on the 86-108MHz bands, whereas two way radios operate on the following bands:
1-86MHz, 108-174MHz, 220-520MHz & 865-920MHz

I don't know which band your radio works on, but not broadcast bands I'm sure.

The only exception to this is the smaller hand helds, which may have FM broadcast programmed, but if this is the case with yours, This issue is out of the realm of two way radio queries, as Broadcast radio is not two way radio, but one way radio, and I'm not competent enough to answer Broadcast radio issues.

Cheers, [email protected] Team

Radio... | Answered on Sep 26, 2019 | 334 views


The usual cause is that the transmit button on the mike is broken or stuck in the "talk" position. If you disconnect the mike and the radio, then turn the radio on and it still is showing transmit, then the issue is inside the radio or the connector for the mike.
If the radio stays in receive mode with the mike disconnected, look at the mike connector for any bent pins or damage to the connector. If you don't see anything, try spraying electronic contact cleaner , the could be some corrosion that is causing a short here. Another thing, if you have it, is to use a different mike and see if that works properly.

Radio... | Answered on Sep 24, 2019 | 132 views


Most headsets do not have a reset since there is nothing to reset. If you need to pair it again with a phone, go into the settings of the phone, find the bluetooth device list and tell the phone to forget the headset. then do the pairing again, after fully charging the headset.

Radio... | Answered on Sep 24, 2019 | 123 views


The overall reports on this radio, which appears to have been discontinued, is that it has a number of problems and needs to be serviced and the circuits aligned by someone with the appropriate skills and equipment. If you purchased it recently, from all reports, see if you can get it serviced under warranty.
otherwise, find a good CB repair shop and have them check it. The likely culprit is a bad transmit circuit. Not a easy fix unless you have the tools to test properly.

Radio... | Answered on Sep 24, 2019 | 151 views

Not finding what you are looking for?
Inland Pro Bluetooth Wireless Headset Logo

0 questions posted

Ask a Question

Usually answered in minutes!

Top Inland Radio Communications Experts

eradiostore
eradiostore

Level 3 Expert

1658 Answers

Brad Brown

Level 3 Expert

18513 Answers

Tom Chichester

Level 3 Expert

60139 Answers

Are you an Inland Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...