20 Most Recent IBM 3581 Ultrium Ultrium Tape Drive - Page 4 Questions & Answers

Epson driver might work. Could try a DOS text print.http://www.fixya.com/support/t976965-problem_printing_ibm_4610_tf6Copy of FIXYA page shown:Question about IBM 4610 TG4 Thermal Label Printer6 AnswersProblem printing with IBM 4610 TF6I have this printer and i can't print with it on windows XP, i connected the printer with RS323 cable and it doen't communicate with the computer, i tried the IBM driver and no good.can u plz help me.royPosted by ras81 on Aug 28, 2008 ras81 Aug 28, 2008 hi the cable is ok, because i already replaced it, the cable is new.... i think it's some kind of driver issue, but the driver on IBM site just won't work. Furqan Sep 05, 2018 Hi I also want drivers for my printer but there are none. How could i find them?6 AnswersBernie RoleBernie Role Expert 199 AnswersDownload and use this driver instead, EPSON TM-88II Printer Driver, 4.00.Good luck.Posted on Aug 28, 2008 Helpful 0 Not Helpful Comment Flagmonk3ybidznessmonk3ybidzness IBM Master 1,879 AnswersUse generic text driver - go for LPT (default port) then change the installed printer properties later.get the serial settings of the printer first (bauds etc).Posted on Aug 28, 2008 Helpful 0 Not Helpful 2 Comments Flag monk3ybidzness monk3ybidzness Aug 28, 2008 add: make sure that it is a 24/9 pin NULL-MODEM serial cable monk3ybidzness monk3ybidzness Aug 28, 2008 Just use the Generic Text Driver type autoexec.bat>lpt1:orC:\>type filename.txt>LPT1:If that works consistently, the problem is probably in Windows.Be sure Windows is set-up correctly with the correct printer driver and something else (another printer, FAX, etc.) is not assigned LPT1: Be sure the 710 is set as the default Windows printer. Try it on another desktop computer. If that works, try another printer on the suspect computer. I have seen cases where a baby AT motherboard was upgraded, but the printer cable/header assembly from the old motherboard was used and caused problems, but that is very rare. Also, the cable connecting to the motherboard could be backwards or loose.Posted on Aug 28, 2008

Hold down the Fn key and press F5

search in google forgot tally password
and download tally password recovery.
if it is demo version then give ur email id i will send u cracked version
it surely help u.
if helpful then rate

I wish to receive the manual or the user manual; my IBM THINKPAD laptop, MODEL R51, 1926ET THIS IN FRENCH AS FAR AS POSSIBLE? THANK YOU

I have not tested any of these free products, but at no cost, you should be able to make multiple copies of the zip archive, and test each software to see if it can be repaired. https://www.raymond.cc/blog/repair-damaged-or-corrupted-zip-archive/ 6 Ways to Repair and Extract Invalid ZIP Files for Free Raymond CC

Unclear - what is your question? You can add information using the Comment menu choice.

Contact several vendors and the non-profit organizations and you may find something that works, or discover a way to get a newer computer (used or donated likely). I supported visually impaired users about 20 years ago, and several government organizations sponsored products that did so. https://www.zoomtext.com/help/contact-us http://www.gpat.org/Georgia-Project-for-Assistive-Technology/Pages/Screen-Enlargement-Software.aspx

Try a different port for the HDMI cable. Sometimes they short out. Hope this helps.

Try booting to Safe Mode, or otherwise getting to System Restore where you can back up to a restore point created before the update. Here's a Google search for causes of that error message: https://www.google.com/search?q=0xc0000135&ie=utf-8&oe=utf-8&client=firefox-b-1-ab

If you can get into the bios, you should be able to tell your system which drive(s) to boot from.

Hello, First open control panel--> Add and remove programs and check if the software is installed or not. If it shows up there click on the start button --> click on All programs--> find the software there you can right click on the icon and set a short cut to desktop. If the above does not work you will need to run system restore first --> then run virus scan --> then reinstall the software.

The function key could be damaged or stuck down. If not, try going to Device Manager. Right click on the Keyboard and choose Properties. Click on Update Driver as it might find something. Reboot the computer. If that doesn't work, go to Device Manager, right click on the keyboard, choose Uninstall, and reboot the computer. When it starts up and sees the keyboard and loads a driver(s) for it, it might fix it. Good luck.

This could be anything from a fried capacitor to a virus. You indicate having ruled out a bad power supply. I assume you can not get to a recovery partition. You might as well see if you can get the machine running, just to narrow down, possibly rule out hardware malfunction. Here is the download site for creation of a bootable USB flashdrive. If you can use the flash drive to get the computer running, perhaps the problem is not a bad motherboard. https://pcsupport.lenovo.com/us/en/lenovodiagnosticsolutions/tools/bootablediags If a virus has taken you down, you might try the Norton Bootable recovery tool. Yes, it goes on another USB stick. If your computer will run (not a bad motherboard), this software should boot it and scan it for a virus. https://us.norton.com/support/tools/nbrt.html Here is a generic page about non booting computer rescue. I thinki you have a computer running XP. You might check dust accumulation inside it. Here What to Do When Your Computer Shuts Off During Startup Once you eliminate a physical cause and a virus, see if you can run chkdsk, boot to safe mode, or access the recovery partition. At some point, you may have to try TestDis, Easeus, or Paragon utilities.

You need a language pack for France, you can download it at microsoft website.

I have found an effective solution, trying which will surely help you in sorting out this issue. so have a look to this thread: https://www.fixtoolbox.com/lotusnotesfix.html

take the hard drive to a JAYCAR shop and they will connect it to a pc to see if it is working if so they have a docking station for sale that you can connect by usb port to your pc and read it through that station

If the password is a power on BIOS password then you have to locate a jumper on the motherboard. If the password is windows related the operating system is XP and you can logon as an admin and change it if the old user has not defeated this feature.