Top 20 Connex Cx-3600Hp 3600Hp 10 Meter 100 Watt Cb Radio Questions & Answers


your power switch it faulty as there is a drop in voltage
does the meters dim down?? then the voltage supply past the power switch it dropping as it draws more current or... the audio ic has damage or one of its associated capactors sometimes a diode can become leeky its used for AM modulation also

Connex Cx-3600Hp... | 171 views | 0 helpful votes


You've been close to another big radio......you think that was a question but I believe it is the answer. The rf amp transitor or the diodes in that circuit have been damaged. So that stage of amplification is not stepping it up for the next. Resulting in the electrical power converted to air audio by speaker isnt available. Cb shops refer to this as a blow front end. Tr17 is the transistor location .......just a side note some radios have a mic circuit check that dulls audio levels this is not the case here.

Connex Cx-3600Hp... | 119 views | 0 helpful votes


Great Question. I'm not sure if Galaxy would work on a Connex . Copper Electronics has a repair department and would probably fix it for you. I'd offer but I don't have a lot of spare time right now. It's probably the power connection inside of the radio or one of the legs on the main volatage regulator broke loose from the pc bpaurd. That's a common problem with those radios.

Connex Cx-3600Hp... | 82 views | 1 helpful votes


This means that your swr is high. you can damage the radio using it in this condition, check antenna and coax for damage or misinstallation

Connex Cx-3600Hp... | 68 views | 0 helpful votes


Use a longer antenna or get it higher..
102" whip for mobiles.
maco v 5/8, army big stik, or Bandit for base. or a long beam 5 or 6 element type.
for example..

Connex Cx-3600Hp... | 149 views | 0 helpful votes


the radio is searching for a strong incoming signal and until it gets one it will search for one. Try turning off the scan button .

Connex Radio... | 88 views | 0 helpful votes


Have you tried keying it without the coax attached ? Take the mic apart and give it a squirt of electrical parts cleaner .Try using a different mic also.

Connex Radio... | 252 views | 0 helpful votes


many trucks have a ground wire in the harness as the cabins are fibre glass or not grounded around the cabin mounts If the radio grounds out through the frame , then there would be no ground for the radio or the aerial wire
to fit this particular may require such a wire in the harness for the radio which it probably doesn't have
As you have been alerted to a problem, it would be advisable to talk with professional radio fitters who work on trucks to get the correct advice before starting on the job
it could save a lot of frustration

Connex Radio... | 33 views | 0 helpful votes


If you disable any part of the radio that does not pertain to CB then you could actually do damage to the radio. the best thing to do is leave it on the CB band and don't touch it.

Connex Radio... | 371 views | 0 helpful votes


Sorry we do not sell parts nor have the ability to locate them for you.

Connex Radio... | 33 views | 0 helpful votes


If you ground the audio wire, you will have no noise or mic function at all. The mic hot wire and the shield should be enough to avoid hum.

Connex Radio... | 101 views | 0 helpful votes


contact connex and they will give you a repair number and let you know where to send it.

Connex Radio... | 201 views | 0 helpful votes


Is the CB getting its power from the amp(?) By amp I will assume you are talking about a signal amplifier..

Connex Radio... | 125 views | 0 helpful votes


people think that if they peak and tune a radio it will work better. First, if its brand new from the factory you shouldn't have to,all you should have to do is lower the dead key raise the modulation and you are good to go . The proper way to do this is with a spectrom analyzer . Do you have one? Cheap on ebay ,may 4000-5000 dollars but if you get one and set that radio perfect you should hear anyone complain that you are interfering with their radio.

Connex Radio... | 248 views | 0 helpful votes


first of all if you do not have a ham license then you should even worry about getting on any band other than the AM band .

Connex Radio... | 150 views | 0 helpful votes


Hello
As a general rule of thumb all radios should be connected directly to the vehicle 12 battery. This connection cuts down on vehicle induced noise and allows the radio to have access to the full current it needs to operate at full efficiency. Make sure there are matched fuses in the positive and negative leads going to the radio.
Hope this answers your question.

Connex Radio... | 153 views | 0 helpful votes


Your connex should have a know with letters on it A,B,C,D,E,F, Look at the counter and set that knob to C whick should be the CB frequency.

Connex Radio... | 1,024 views | 0 helpful votes


On the RF Hi Lo switch do you have power? Is the switch ok? That switch regulates the TX power and if it is open, you have none.

Connex Radio... | 119 views | 0 helpful votes

Not finding what you are looking for?
Connex Cx-3600Hp 3600Hp 10 Meter 100 Watt Cb Radio Logo

9 questions posted

Ask a Question

Usually answered in minutes!

Top Connex Radio Communications Experts

Brad Brown

Level 3 Expert

18519 Answers

Tony Raia

Level 2 Expert

264 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Connex Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Connex Radio Communications

  • Connex Radio Communications

Most Popular Question

bought cx 3600hp 2 years ago stop

  • Radio Communications
Loading...