20 Most Recent Jet Tech Systems 39 in. F22T Free-standing Dishwasher Questions & Answers


It depends on how old is the machine. the more recent unit (5 years) used door guide (green) #16468. Search by part number or description

Jet Tech Systems... | Answered on Jul 15, 2014


a plug can be warm. if it is hot to the touch, stop using it and have the machine checked and the receptacle check by a qualified technician.

Jet Tech Systems... | Answered on Sep 02, 2014


for models equipped with a drain pump;
verify that the pump is not clogged. if it hums during the fill cycle or rinse cycle then something is lodged inside. If it doesn't then it needs to be replaced.
for models without the drain pump;
something is interfering with the water flow. when the stand pipe is removed, the tank should empty in about one minute.

Jet Tech Systems... | Answered on Sep 02, 2014


Most Jet-Tech dishwashers has one adjustable rinse thermostat and one fixed wash thermostat. The wash thermostat can be substituted with an adjustable thermostat. Location depends on the model. F-18 are located on top. F-22 are located under next to the wash tank. Search by part number or description

Jet Tech Systems... | Answered on Jul 15, 2014


On the F-14, the booster thermostat must be satisfied. The rinse thermostat must work properly and or the rinse heater. follow the diagram. This kind of troubleshooting is done by qualified technician. Remember to unplug the unit before opening the panels. It could be just a burnt wire on the rinse booster heater connection.
. 39986f38-1a20-4562-92ba-c0c84a39bf50.jpg

Jet Tech Systems... | Answered on Jul 15, 2014


The detergent system on the Jet-Tech machine are all very similar. Near the solenoid valve under the machine, beside the drain connection, there are two wires, one red and one blue. Those wire will run the detergent pump when the machine calls for water. Two tube are attached to the pump. when looking at the pump from the front or clear plastic can be seen, the tube on the left (arrow going up) is connected to the container with the detergent. the tube on the right (arrow down) is connected to the back of the unit to inject the detergent into the tank. Some precaution should be taken to assure that the connections are tight and not leaking. if the tube shows signs of crystals inside, it should be replaced as the detergent as crystallized within. Search by part number or description

Jet Tech Systems... | Answered on Jul 15, 2014


If the machine will fill on its own when it is empty then the rinse cam on the timer is defective

Jet Tech Systems... | Answered on Dec 29, 2013


No idea as i would either make my own or go to general store in alicante and ask the nice man if he has anything that would do the job if the original parts were not available

Jet Tech Systems... | Answered on Dec 25, 2011


www.jet-tech.com/products/F-18DP/f18_tech_manual.pdf

Copy and paste that link into your internet address bar or type it in.
That is your manual

Jet Tech Systems... | Answered on Sep 22, 2010



Hi,

That is not that hard to fix and you can easily buy the parts yourself online...

Here is a tip that will help you with the online buying...

How to Buy Appliance Parts Online

heatman101

Jet Tech Systems... | Answered on Sep 01, 2010


If this is a common problem then ring the manufacturer, if not you will need to have it replaced.

Jet Tech Systems... | Answered on Aug 03, 2010


There are two screws that hold the plate in. Because they are recessed, you may not think they are the right screws. Look at this video for a step by step.
https://www.youtube.com/watch?v=Co8iNquHOLc

Dishwashers | Answered on May 25, 2020


To access the dishwasher filter, remove your lower dish rack to expose the bottom of your dishwasher. You can find the filter in a back corner of the tub bottom, or around the base of the bottom spray arm. Some dishwashers have a triple filter system with two parts: an upper filter assembly and a lower filter.
https://www.maytag.com/blog/kitchen/how-to-clean-dishwasher-filter.html

Dishwashers | Answered on May 20, 2020


Check the drain tube routing to the drain pipe. It should be positioned at some point higher than the entry location to prevent water running back to the dishwasher. Some dish washer detergents can plug the drain causing the back flow.

Dishwashers | Answered on May 20, 2020


Hi we have a Hoover DT999 and according to the manual for that machine error E1 is water inlet tap turned off

Dishwashers | Answered on May 18, 2020


mine is doing the same what can it be

Dishwashers | Answered on May 16, 2020

Not finding what you are looking for?
Jet Tech Systems 39 in. F22T Free-standing Dishwasher Logo

2 questions posted

Ask a Question

Usually answered in minutes!

Top Jet Tech Systems Dishwashers Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Brad Brown

Level 3 Expert

18342 Answers

ray gallant

Level 3 Expert

67977 Answers

Are you a Jet Tech Systems Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Jet Tech Systems Dishwashers

  • Jet Tech Systems Dishwashers

Most Popular Question

find door gasket f2 jet tech

  • Dishwashers
Loading...