20 Most Recent Linksys USB200M USB 2.0 Network Adapter Questions & Answers


One light is out

It depends on which light is OFF: Below are the LED indicators:

100/ACT Green. The LED lights up when there is a connection to a 100Mbps network. It flashes when the computer is transmitting or receiving data at 100Mbps.

F/H Green. The LED lights up when the Adapter is operating in fullduplex mode. The LED is off when the Adapter is operating in half-duplex mode.

10/ACT Green. The LED lights up when there is a connection to a 10Mbps network. It flashes when the computer is transmitting or receiving data at 10Mbps.
12/8/2009 9:57:29 AM • Linksys USB200M... • Answered on Dec 08, 2009

Dont have the CD to install ,now trainig to use

If you are talking about the item in the picture, you can find the driver at the following address:


There are two versions of the driver, so you have to look at the device and see which version is it. (Version 1.00 or 2.00).
11/14/2009 7:31:11 PM • Linksys USB200M... • Answered on Nov 14, 2009

I have jumped through all your hoops to try and up

Wrong site millhouse. This is your first post, so no one has made you jump through hoops. You haven't been very smart in asking a question, which is what this website is designed for.

Please state a question or send your laptop back to me, i will give you an address if you are stupid enough.
7/7/2009 7:27:05 PM • Linksys USB200M... • Answered on Jul 07, 2009

Want to add a network adapter to my laptop

I sometimes have problems with cookies on the linksys site so


Go to support
(choose North America and US as appropriate)

Choose Linksys Windows Vista Support on left blue bar.

Choose Download Drivers toward center of page

the 5th line under adapters is USB200M V2 (version 2 of the adapter) - if this is your adapter's version (there is a version 1 of this adapter too) there appears to be a 32 bit Vista driver.
2/7/2009 1:28:41 PM • Linksys USB200M... • Answered on Feb 07, 2009

Offline (vista0

If you are using the USB200M network adapter, you should go into device manager and see if it shows up. If it does, there is a little pop up connector on this device that sits more or less on a 45 degree angle and you just insert on end of the ethernet cable in this until it clicks. You should have connection. If not uninstall by right clicking on this device in device manager(if present) and install drivers FIRST then insert device into any available USB port, new device should be found and drivers will be installed, sometimes it may be necessary to insert this device first and then install software that came with the device, but as a rule ALWAYS install drivers FIRST ..
7/25/2008 11:05:02 AM • Linksys USB200M... • Answered on Jul 25, 2008

Usb problem

Plug in usb drive, click my computer and locate usb device in windows explorer. right click on usb device and choose format.
5/17/2008 7:27:19 AM • Linksys USB200M... • Answered on May 17, 2008

ALL usb2

hi my usb not format pl help
5/17/2008 7:13:08 AM • Linksys USB200M... • Answered on May 17, 2008

Usb network adaper wuth speedbooster

The USB200M should be version 2 to make it work with Windows Vista. You may verify it by looking for the exact model number on the adapter itself.

Click on the link then click on "32 bit" on USB200M v2 to download its driver for Windows Vista.

5/2/2008 10:48:21 AM • Linksys USB200M... • Answered on May 02, 2008

Linksys Psus4 printserver for usb with 4 port which i'm using to connect my hp1020 printer on the network ???

Hi please go through this link

11/16/2007 3:49:36 PM • Linksys USB200M... • Answered on Nov 16, 2007

How i do the setup of my Linksys Extender?

Unplug the power cables of the router and the range extender for 30 seconds. Plug in the router first. Wait for all the lights to be stable then plug in the range extender. Your range extender should now be in synchronized with your router.

Manually configuring a Linksys Wireless-N Range Extender

https://www.google.com/search?q=setup+Linksys+Extender ..
2/8/2022 2:18:04 AM • Linksys... • Answered on Feb 08, 2022

Frontier router

Frontier Router Login at the bottom of the Network Connections window, just below the address bar. Select Wireless Properties from the menu. Locate the Network security key field on the Security tab. You'll see your Wi-Fi network password if you click the box for Show characters.
1/28/2022 7:46:04 AM • Linksys... • Answered on Jan 28, 2022

How do I connect my Linksys router up to my existing router to stop buffering?

You can use rj45 cable to it .
10/24/2021 11:44:43 AM • Linksys... • Answered on Oct 24, 2021

How to Fix Linksys Router Error 2118?

This seems to be a symptom of a configuration error, which can be fixed by resetting the router to factory default. Do this by finding the (often partially hidden) reset button on the device, and pressing and holding down the button, with the power on, till lights start flashing on the router. Let go of the button and allow the router to reset (can take a minute or two). You will now have reset the router to factory default. To connect to your ISP, you'll need to enter your account details (and any other specific information) provided to you by your ISP. You will also have to set a name and password for the wifi section of your router (if it has wifi) if you don't want it to be freely accessible by everyone within wifi range.
7/29/2021 11:33:41 AM • Linksys... • Answered on Jul 29, 2021

Linksys WRT54G2 V1 suddenly stopped working

Disconnect the power to it, wait 5 minutes and power back on.
7/13/2021 1:37:57 PM • Linksys... • Answered on Jul 13, 2021

Why is my Linksys WRT54G wireless-g router not being recognized anymore?

just fixed one yesterday. the power pack was no good.AC wall wart, power green LED blinked endless. and the white logo, LED is dead.. a new pack fixed it. also the wrong pack used, ! do not mix them up. oops. first year 54G, v1 uses 5vdc pack. at v2, and up all want to 12vdc pack, bottom sticker on above failed was v6. you said recognized, does that mean the 4 rear Ethernet wired jacks are dead, or just wifi dead.? first the ethernet ports must work, or wifi is doomed.
2/18/2020 11:46:05 AM • Linksys... • Answered on Feb 18, 2020

How to fix Linksys router error 321 ?

Good day, This might be of help . Steps To Fix Linksys Router Error 321:- Step1:- Check the Firewall Settings To check the Firewall Settings is the first priority for the users. Then check the firewall settings of the computer/ Laptop, will be helpful to find the problem. If there is any firewall installed on the computer, so the users need to turn it OFF.During the process, the users ensure that the Local Area Connection on the computer is not disabled. The Local Area Connection should not have any static IP address assigned. If there is any then the users need to immediately set the IP address to automatic. Method2:- Run the Installation CD Again:- The users require trying to run the CD again and ensure when the CD runs, it will ask to connect the computer and the modem to the router with the cable. So the users will need to notice, that there all the lights lit up on the router. If it's not, then users will need to setup their router without the CD. The users can get the instruction to setup router manually in the method 3. Step3:- Try to Setup Router Without Installation CD Setup Linksys Router without Installation CD is another best option for users in order to completely avoid the in order to fix Linksys Router Error 321. Follow the below-given instruction to Setup Linksys Router without Installation CD: First of all, connect the main computer to the Ethernet port on the router. Then the users need to connect the modem to the Internet port on the router. Now it's time to verify the status of the light that is blinking properly. Next, users need to open the setup page of the Linksys Router and then change the Internet connection settings manually. In the setup page of the Linksys Router, the users can change the settings of the router as per their needs. Then the default IP address of many Linksys router is And the default username and password would be an "admin". Wait for a few minutes, when the main computer is able to access the Internet, so users need to create a wireless network for their wireless computers/devices. or you can call them @ Toll Free 1-800-204-6959 that is Lynksys support.
2/3/2020 1:14:25 PM • Linksys... • Answered on Feb 03, 2020

LinkSys SuPport NuMber $1{877}*[717]*^{0727} in USA/CANADA

Setup helps
11/26/2019 11:52:55 AM • Linksys... • Answered on Nov 26, 2019
Not finding what you are looking for?
Linksys USB200M USB 2.0 Network Adapter Logo

12 questions posted

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Donivan Wise

Level 2 Expert

254 Answers


Level 3 Expert

4383 Answers


Level 3 Expert

3290 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Linksys Computers & Internet

  • Linksys Computers & Internet

Most Popular Question

usb network adaper wuth speedbooster

  • Computers & Internet