20 Most Recent Belkin F5D7130 And F5D7010 (Bundle) 802.11g/b (f5d7130/f5d7010) - Page 7 Questions & Answers

You can also try to connect this device using a wired connection to your computer or laptop Running Windows 7 or Windows 8. The first thing to do, is make sure that you press the little reset button on the device so that the device memory is cleared. Then all you have to do is open up Google browser or Internet Explorer and type in and hit enter, and that will bring you to the Belkin Setup Menu. From here you can add this device to any home or office network just follow the on-screen step-by-step instructions

Belkin Computers... | Answered on Apr 21, 2017

You have to go into the setup for the router. Most default to the IP address. You would type that address into your internet browser and hit enter. Then you will be asked for a name and password. If you have your belkin manual it will tell you the default name and password. Once in the settings you can change the password. You can also turn off SSID broadcasting, enable the highest level of security that your particular router supports in conjunction with your computer and enable MAC authentication. If you enable MAC authentication you have to type in the MAC address for each device you wish to have access to the router.

Belkin Computers... | Answered on Apr 21, 2017

If this is a Belkin N300 router the default username and password will be the following :

Username: admin

With one of the following passwords :

Password: password
Alt. Password: 1234
Alt. Password: 12345

If you have ever changed the username/password and have forgotten them, you can reset to default by following below procedure (This will reset all settings to factory defaults) :

Press and hold the "Reset" button for at least 10 seconds, and then release it. The lights on the Router will momentarily flash. The "Router" light will begin to blink. When the "Router" light becomes solid again, the restore is complete.

Belkin Computers... | Answered on Apr 16, 2017

Just change the BIOS from IDE to SATA, that's all I did.

Belkin Computers... | Answered on Apr 06, 2017


When we plug in any USB hard drive or printer, sometimes in this router it will not show the light but the hard driver/printer will be getting deducted.

But if its not getting deducted, then follow these steps,

1. Open up the internet explorer in the comp in which you are online and clear the address bar and type in the number and hit enter. You will be logged into the Belkin router setup page.

2. In the left hand side click on Firewall , when its asking for the password to login, leave the password as blank and click on submit

3. You will find the firewall: ENABLED, change it to DISABLED and click on apply changes.

4. Then power cycle the router for 30 sec (Unplug the power cable of the router and plug it back in after 30 sec)

5. See whether the hard drive/printer is getting deducted even if there is no light for the USB in the back of the router.

6. Still if its not getting deducted, then disable the Firewall in your computer (Windows and other third party firewall like NORTON, SPYWARE, or other antivirus software.)

7. If still if its not getting deducted, Uninstall the Belkin router Monitor software from the ADD/REMOVE PROGRAMS and then reinstall it using the CD.

8. Right click on the Belkin Belkin router Monitor icon on the lower right bottom corner in the task bar and click on CONNECTED USB DEVICES.

It will be deducted, if not the its obvious the router USB slot is defective. Replace the router in the stores if you have bought it within 30 days or contact BELKIN technical support 1 800 2235546(toll free) and get your router replaced.

With regards,


Belkin Computers... | Answered on Apr 03, 2017

its on the router its letters y numbers

Belkin Computers... | Answered on Mar 09, 2017

to get to the set up page open the search page ( google or the like ) and type in and that will open up the access to the router settings
when entering the router /modem code ( from the back of the unit ), you have to enter it exactly as it is case and number specific things like o O 0 ( o is little letter o, O is capital letter o and 0 is number zero) are a source of problems because the lettering is small and confusing so enter what you think it is , then again with the change and again if still not connecting
you may have to get the unit manufacturer or service provider to give you the figures for the settings after you get the page open

Belkin Computers... | Answered on Mar 08, 2017

Usually when a UPS fails, the cost of a replacement battery makes replacement of the complete unit the desirable alternative.

Belkin Computers... | Answered on Mar 06, 2017

The blinking orange power light suggests that there is a problem with your modem. The modem should be plugged into the top ethernet port of your router. Try turning off your modem for 10 seconds and then turning it back on.

Belkin Computers... | Answered on Feb 16, 2017

The only thing on the cd is usually just a manual. If that is what you need, you can download it here:
How to find your Belkin routers user manual

Belkin Computers... | Answered on Feb 02, 2017

Not finding what you are looking for?
Belkin F5D7130 And F5D7010 (Bundle) 802.11g/b (f5d7130/f5d7010) Logo

Popular Tags

6 questions posted

Ask a Question

Usually answered in minutes!

Top Belkin Computers & Internet Experts


Level 3 Expert

4369 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Lee Hodgson
Lee Hodgson

Level 3 Expert

4810 Answers

Are you a Belkin Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Belkin Computers & Internet

  • Belkin Computers & Internet

Most Popular Question

anyone know get setup

  • Computers & Internet