20 Most Recent BenQ DC C30 Digital Camera - Page 3 Questions & Answers


Well to connect arlo camera with alexa follow the steps:
1. Make sure that your Arlo camera is powered on and connected to the cloud.
2. Enable the Arlo skill in one of the following ways: Ask Amazon Alexa "Alexa, enable Arlo skill" to receive instructions in your Alexa app to link your Arlo account with your Alexa account.
If that not resolving to contact us Call:1-888-356-3444 or visit our website https://alexacustomerservice.com/ https://alexatechnicalsupport.com

Cameras | Answered on Nov 12, 2020


You can try removing batteries and then try the update again. Firmware updates must be the only thing on the SD card and the update package must be unwrapped. Read the instructions carefully. Sometimes a second update will work, but Firmware updates alter what happens before the operating system loads. Usually, the device has to go back to the maker.

Cameras | Answered on Nov 10, 2020


With the help of Bitwar PDF Converter.
Note: The software is now offering a free 30-day trial for new users.
Step 1: Visit the Bitwar PDF converter official website to download and install it.
Step 2: Open Bitwar PDF Converter and choose Split PDF tool from the Other PDF Tools menu.
Step 3: Add the PDF file and choose the pages that you want to delete.
Step 4: After selecting pages, click Convert and Open path to preview the new PDF file!

aed020f4-7c1e-4e83-88cc-c3b2bccc2cb8.png

Cameras | Answered on Nov 02, 2020


Your stealth cam may not be intended for outdoor use.

Cameras | Answered on Oct 30, 2020


Has it been formatted ? If you have read it in your computer without setting write-protect, the computer will have written hidden files to it which the camera cannot understand.

Cameras | Answered on Oct 29, 2020


User manual. Normally, the spring contact goes on the negative and the positive is the flat end. It is shown in the diagram anyway.
https://www.nebotools.com/product_images/9016156_User_Manual.pdf

..

Cameras | Answered on Oct 24, 2020


Not familiar with the model but I think most point and shoot cameras are similar to each other - if that is so you should find a delete option in a menu when you are viewing the picture you want to delete.
You can also delete by connecting to a computer or using a card reader with the computer and and deleting single pictures or whole files.

Cameras | Answered on Oct 24, 2020


The device is not meant to have the battery changed (?!).
However, I am going to drill out the holes where the screws would go and try and change them myself. It doesn't not make 'consumer' sense to me to have this unit without being able to change the battery. It has a 5 year battery life but I only need this unit once in a while so in 5 years I may only use it once or twice.

Cameras | Answered on Oct 21, 2020


Google

make model manual

but....

MSDC stands for Mass Storage Device Class. It is the most significant part of camera, which is required to bond camera and computer. If there is any damage/corruption in internal File System structure of the card then MSDC fails to detect the card, so MSDC read sector or MSDC write sector error in memory card arises.

Fix MSDC Sector Error in Memory Card - Yodot

Cameras | Answered on Oct 20, 2020


R817 value is 2.2 k and Clor is red red red golden

Cameras | Answered on Oct 19, 2020


If it is saying "non-playable file" it usually means the format the photos are saved as isn't one the player recognises. Basically, The photos are in one language and the player doesn't understand it. If you or someone you know is good with computers the photos can be reformatted, (translated), into a form the player understands. It isn't a hard thing to do and most laptops and computers have software built in that will do it easily and quickly.

Cameras | Answered on Oct 14, 2020


There's probably a port for a cable to attach...USB/HDMI/? Depends on the camera. Try to figure out the attachments needed on each end, and order that cord from Amazon. Or, just take your camera to Best Buy and let them help you. Normally, once you attach the cable to the camera and computer; your computer will recognize it. Then transfer the pics to a designated folder for viewing. Hope this helps.

Cameras | Answered on Oct 13, 2020


First, eliminate some of the possible causes:
1. Is the battery low or dead? Use a fully charged battery.
2. Is there an obstruction causing the lens from3 opening or closing - such as sand or other particles.. They have to be removed.
3. Did you drop the camera? That might damage the zoom gears or put the lens out of alignment. Do not shake it. If this has happened, an expert tech might have to disassemble it and adjust. This could get expensive, depending upon where you had it done.
4. Is there an uneven gap between the lens and the lens housing? Turn it off, place it face up, look. If so, apply gentle pressure at the highest gap in order to snap it into place. You should hear a click. Power it on. If it extends and contracts power it off, then try to move the lens in a circular motion until it clicks. Power it on. Twist the largest lens ring until it clicks.

Cameras | Answered on Oct 10, 2020


Slyde King go to the website. In the lower right corner view the video. Pay close attention to the memory power setting. It is possible the setting is not what you want or the circuits that control the power setting are failing.

Cameras | Answered on Sep 26, 2020


My last pay check was $9500 working 12 hours a week online. My sisters friend has been averaging 15k for months now and she works about 20 hours a week. I can't believe how easy it was once I tried it out. This is what I do.Click For Full Detail.

Cameras | Answered on Sep 25, 2020


Take the card out and check if the lock switch is in the locked position. You need to move it to the unlocked position. That means moving the switch away from the SD card pins and towards the back of the card. If the lock is damaged or loose, you may need to replace the SD card. To see what the lock looks like, see https://kb.sandisk.com/app/answers/detail/a_id/1102/~/sd%2Fsdhc%2Fsdxc-memory-card-is-write-protected-or-locked .

Sometimes, you need to use a computer to format the SD card. This can happen when the card was initially formatted to be used with a different device. Then return the card to the camera when the camera is off. Follow the steps to select the Custom setting and format the card again in the trail camera. See page 20 of the manual, https://www.stealthcam.com/wp-content/uploads/sites/2/2017/12/STC-G42NG-KPT.pdf . The last thing to try is a firmware update of the camera.

I hope this helps.

Cindy Wells

Cameras | Answered on Sep 20, 2020


Pleasse check if the camera of the video is turned off -
check the settings under my devices -

Cameras | Answered on Sep 01, 2020


Maybe it's just sulking - try taking it tea in bed tomorrow

Cameras | Answered on Aug 30, 2020


Where the manual suggests you insert it.

Cameras | Answered on Aug 30, 2020

Not finding what you are looking for?
BenQ DC C30 Digital Camera Logo

0 questions posted

Ask a Question

Usually answered in minutes!

Top BenQ Cameras Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Vincent G
Vincent G

Level 3 Expert

2363 Answers

ChinthakaJ
ChinthakaJ

Level 3 Expert

943 Answers

Are you a BenQ Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

BenQ Cameras

  • BenQ Cameras

Most Popular Question

benq lithiumion battery pa pack 3 7v

  • Cameras
Loading...