20 Most Recent Cisco Catalyst 4006 Chassis ( 4006) - Page 6 Questions & Answers

you have to contact your service provider

you need to install sound drivers plus all the other drivers for your device, it is almost certain they are not installed if you have a bare windows installation only

Huh? Punctuation will only help us understand what you're trying to do!

I doubt you can. Best advice is to connect any computer to the wired network open the web interface

The Cisco switch will probably err-disable the port when you plug it in. The workaround is to add these commands: Switch(config)#service unsupported-transciever Switch(config)#no errdisable detect cause gbic-invalid It'll either work or it won't!

IP Lite introduced enterprise access Layer 3 features to the Cisco WS-C2960XR-24TS-I. IP Lite is subset of IP Base features. Some of the IP Lite features are: Routing Information Protocol (RIP) v1 Routing Information Protocol (RIP) v2 Open Shortest Path First (OSPF) v2 Routed Access Open Shortest Path First (OSPF) v3 Routed Access Enhanced Interior Gateway Routing Protocol (EIGRP) stub Equal-cost routing Hot Standby Router Protocol (HSRP) Protocol Independent Multicast PIM (Sparse Mode, Dense Mode, Sparse Dense Mode, Source Specific Multicast) stub Virtual Router Redundancy Protocol (VRRP) for IPv4 Private VLAN IPv6 First Hop Security source guard Per-VLAN and per-port policershttp://www.3anetwork.com/cisco-ws-c2960xr-24ts-i-price_p1874.html

The Cisco Catalyst 2960-XR switch models have the following additional capabilities in addition to the features in the Cisco 2960-X models: Dual-FRU power supply with integrated fan Layer 3 features with IP Lite feature set Configurable 8 queues per port (standalone) 48 Ether channel groups http://www.3anetwork.com/search/2960x

call cisco

No, both of them are power supplies. PWR-2911-AC is the standard power supply but the PWR-2911-POE is a bigger power supply to power up EHWIC or single/double-width line cards. Moreover, there is no physical way to put two same/different power supplies into a 2900 router. But 3800/3900 routers can support dual power supplies. Cisco 2900 Router Price Buy Cisco ISR 2900 Series Routers 3Anetwork com

1) FR should be supported in IPBase license >>Offers features found in IPBase IOS image on ISR 1800,2800 and 3800 + Flexible Netflow + IPV6 parity for IPV4 features present in IPBase. note X.25 is mentioned in the first table FR it isn't. 2) You need to purchase a PAK and you should be able to generate the DATA license SAL from the portal following the instructions (there are also other methods described in the document) 3) you need SEC for IPSec VPN it means another PAK to buy 4) yes you can install all of the additional licenses in a single device 5) yes, they build on IP Base so you add features without removing any 6) no, the new device will be already with the correct licences from factory >> On each shipped device IPBase software activation key is installed by default. Additional keys are installed by manufacturing depending on the customer order. 7) yes with the UC PAK Hope to help

This problem is hard to answer, i think u can refer to the material about Cisco STP, if u still don't know it clearly, u can send email to our CCIE expert [email protected] to solve ur problem. : )

You can choose the transceiver SFP-10G-ER or GLC-EX-SMD, these two all can transmit up to 40KM. and more than 75% OFF at 3Anetwork.com for Cisco optic transceiver.

The main difference between WS-C2960X-24TS-L and WS-C2960X-24TS-LL as below: WS-C2960X-24TS-L 4 SFP Uplink, WS-C2960X-24TS-LL 2 SFP Uplink. WS-C2960X-24TS-L supports FlexStack-Plus stacking while WS-C2960X-24TS-L does not. WS-C2960X-24TS-L with LAN Base feature set, WS-C2960X-24TS-LL with Lan Lite feature set. I hope it can help you. WS C2960X 24TS

You probably need a new box. Contact your cable company. I might not mention the part about your son and the water....

Depends on the device. Have to go to a Cisco forum for the quickest help or directly to Cisco. Just call them. Act like it is urgent! :)

If you can't hardware reset by pressing the reset at the bottom of router for at least 5 seconds then you need to do a software reset.click on following link to go through the right procedure..... http://kb.linksys.com/Linksys/ukp.aspx?pid=10&vw=1&articleid=3676 please vote thanks.

I am assuming you are referring to the console ports on your cisco Router. You need a terminak emulation program and a serial port on your p.c. Once you connect to it set up the Vlan interface so you can use the fast ethernet interface to connect. https://www.hilgraeve.com/hyperterminal/ http://en.wikipedia.org/wiki/List_of_terminal_emulators

being cisco it could be anything as system administrator can set it to anything they like.

Cisco Quest is a cloud access system, if you disable it you may loose your access to your desktop storage, apps etc. Have a look in your start-up applications to see you can disable it temporarily, to see what effect it can have. Type in "msconfig" in the run box to access the start up applications list.