Top 20 Sharp " AQUOS 70"" Class / LED / 1080p / 120Hz / HDTV LC70LE732U" Questions & Answers

Is there a media card in the camera ?

Use the "Macro" setting, that setting looks like a little flower.

hi there, this is all i could find out at the moment. it could be the latching system i am not sure if its electronic latch or spring. start by looking there if its electronic latch take it in to a shop if its spring latch maybe the end of the spring just needs putting back on. The chances are that a switchcontact or motor is not engaging, and the unit will have to be opened up to be fixed. Oftentimes, with these older units, switch or relay contacts become oxidized over time, and fail.. all this info i found from or fixya site. hope this might help you out.

Yes it is due to a defective battery

Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary. Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

Fault to the main power supply regulator section. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electro-medical.blogspot.com/ http://electronicshelponline.blogspot.com/ It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.

M stands for macro.this is for extreme close so dont take photos with m displayed unless extreme close

You should be able to use the buttons on your TV to adjust settings. Using the menu channel and volume buttons to navigate the menus.

Sounds like condensation is forming on the inside of the camera lens or housing glass.

There is no tripod mount on this model.

Make sure the memory card is properly installed in the camera and is formatted. Also make sure it is the proper type and size rated for the camera. The connections from the camera to the memory card may be dirty or loose , also the memory card could be bad.Try a new memory card of the proper size if none of this works look for a new camera or see about having it repaired.

According woth your model, look in the Sharp site some Win7 driver, sometimes is diferent drivers for XP or 7.

Keep us updated.

Hi - Sorry your having problems with your camera. I'm assuming it's a video camera. the DEW warning is telling you there is excessive moisture in the camera. I suggest you take out the tape and leave the tape door open in a dry warm place for a couple of hours.
You could also take a hair dryer on LOW and keeping it at least six inches from the camera move it back and forth over the tape compartment for a minute or two.
Sometimes the DEW message comes on when there is no such problem which is a problem with the camera that will probably require service.

Good Luck, Mikeywaf.

Can you tell me the model of your device...
so I could give you the exact driver and procedure to install it.

Just post back.

Hi,

To order the replacement cable for your camcorder, you will have to contact the manufacturer's customer support department.

Here is the link to Sharp Europe contact page:
http://www.sharp.eu/cps/rde/xchg/eu/hs.xsl/-/html/contact.htm

Also, you can contact Sharp (Spain) customer support on this number (902 101 388) and check whether they have the replacement cable.

Hope this helps you. For more help and clarifications, please feel free to reply to this post with the complete model number of the camcorder.

Thanks for using FixYa.

go to menu on your camcorder and turn off the remote, that worked for me

Visit to the given link
http://sharecash.org/download.php?file=631280
please rate the answer if you find useful
thanks for rating............

You do not need the driver just press the power button on the remote and it will come up as a removable disk

You can get the manual on link below. You need model # though.


http://www.skyscan.info/content/manuals.html

Visit this website, it could be of help. However, you need to supply detailed information of your Digital Camera including the model and all accompanying information.
http://forum.devicemanuals.com/
Please indicate if this solve your problem.