HP Officejet 6500A Plus Wireless e-All-in-One Inkjet Printer, Copy/Fax/Pr - Answered Questions & Fixed issues

You don't say what trouble shooting you've done. So lets start with the basics: 1) make sure your power cable is plugged all the way in from the back of the printer to the power strip. Make sure your power strip is on. (cannot tell you how many times this has been my problem). Make sure the plugs on both sides of the transformer (the black box in the power cable) are plugged all the way in. I'd unplug and replug everything. 2) The power button on this machine is not real obvious. It is to the left and aligned with the top of the control panel screen. I've attached a picture. 3) if that doesn't do anything open the cartridge access panel. The machine should light up, give you an error message on the control panel. 4) if none of these work and you've rechecked your power, I'd take it back to where you purchased it.

If your printer screen is blue and shows and error code, the problem is less likely with the screen. Most likely there is some disconnected wiring or formatter board is bad. The two videos below may help you in this issue.:

Try removing screen and see if anything has disconnected in the back. Removing screen is easy. See video for instructions:

Remove the screen and see if it disconnected somewhere. There is really no way to just calibrate it otherwise. See this video on how to remove screen:

That means that either the scanner window or the sensor is dirty and needs to be cleaned http://support.hp.com/sg-en/product/HP-Officejet-6500-All-in-One-Printer-series---E7/3795309/model/3944625/document/c01658811

This might be the issue.... The paper still has to pass through the magenta even if its not used but being empty it might not register the toner hence not allowing you to print at all.

buy genuine cartridges next time, mine did same thing when changing them, ok now.

I would suggest that you use the machines own programme to clean the ink heads

Have you checked for any paper jams? If there are no paper jams, remove the loaded paper and separate the pages by "fanning" the paper If all the above do not work, use a bit of rubbing alcohol on an earbud and clean the pickup points on the paper roller.

My reply that won't post maybe you can send on:http://h30434.www3.hp.com/t5/Printing-Issues-Troubleshooting/How-do-I-reset-a-general-printer-error-0x61011beb-on-my-HP/td-p/2260611

Do you mean the error 0x6101bed? This appears to be an error with the printer carriage or the sensors that detect paper in the trays. Unplug the USB cable if you are using that connection before trying the steps below. Some people have solved the problem by turning off the printer and then removing the photo feed and output trays. Also remove any extras like a duplexer if you have one. Put in a sheet of plain paper. Then turn on the printer and quickly press the Menu button. Find the menu item for printer reports and select print status report (or a similar item). Push the paper gently into the printer pickup until the pickup spool catches the paper. Press Cancel and see if the printer ejects the sheet. Some people have found that adding a few extra power on/off power cycles (5-6) helps. Then try to to move the print cartridges (gently - do not force anything) while the printer is off. While you are trying to move the print cartridges, check for any foreign objects in the printer. (A small piece of paper can cause the bed error.) Make sure that the printer is on a firm surface wider than the printer. Pick it up and put it down again to shake things loose inside. At some point, the printer will go into a initialization step if you have solved the internal issue. If these don't help, it may be that the internal frame and the rail that the printer cartridges ride on is bent. Then the solution is probably to replace the printer. I hope this helps. Cindy Wells

This could be your default print settings telling the printer to use mono all the time. Go into control panel or Devices and Printers, get the printer queue up, or the settings if you can remember where they are (i forgot!), click Printer then click properties. In the option tabs at the top, if it's the correct driver for the printer you should find an option under general called Preferences. Click this and you should find the default settings for the printer including paper sizes and colour/mono printing modes. Hope this helps?

Simply turn off your printer and restart it - It will through the paper out

Make sure that the cartridge has it's plastic sealer tape off and make sure the cartridge is still a usable item - liquid if is should be liquid, etc. Worse case, get a lint-free cloth - soak a spot in hot wther and wipe the head off in one-direction only - then re-install. Next, insure you have gone through HP's steps to install a new cartridge and hopefully that will do it.

Download latest HP software and install it. After installed go into settings and dig thru it until you find the ink monitor settings, un check box and reboot computer and printer. The monitor should now be off. HP lost the lawsuit and was supposed to add an update to allow users to disable the ink monitors on most of their printers. Some are not under the lawsuit conditions so if you have one of these there is no way to defeat it, its all handled in printer IC board and not windows. I’m happy to help further over the phone at https://www.6ya.com/expert/david_c087e4b7d13c0163

You can usually can only alter or darken a print colour from the software program (i.e. Word), then send your document to the printer.

Turn printer on. Lift the entire top of the printer up. The ink cartridge tray will come to the center of the printer. Push the plastic tab of the cartridge you want to replace and lift it up and towards the back.Remove all wrappings on your new cartridge and reverse this procedure to re-install.

Usually on hook telephone line voltage around 40V DC +/- depends on exchange, voltage will drops below 12VDC if its half hook..You will get engage tone/usage tone if voltage drops less than 12V, in this condition you wont get any incoming calls. You need to open the printer formatter to locate the modem where telephone line inserted.. Let understand why this malfunction happens.. The ring voltage between the line is +120V AC, but it should not exceed more than 200V.. To protect the circuit, line will guarded by component called "VARISTOR". The Varistor will burns if voltage reaches specified or more voltage across it.. Once varistor burns U will get engage tone always... Basic multimeter is enough to check the varistor, put multimeter in diode mode, test both ends of varistor, it should not show zero value or beeping. Some times it may burn, blast or bulge. Remove the faulty component from the circuit with the help of soldering iron, connect the line & verify, if line is good replace with same rating of component.. Chk for the ring & dial tone... Req tools: Multimeeter, soldering iron, little paste & Led, screw driver set for opening the printer.. Depends on design varistor may fix accordingly which we need to find out the location.. But its always fixed between line in path. pl see the attached sample diagram. if you are non technical pl don,t try it...Best of luck.. Ex: Varistor Damaged/burnt varistor

the problem could be with print heads not in cartridgestry to replace print head it one part

WPA code? it should be on the bottom of the router on a sticker. It's the same code usually used for wifi too. Hope this helps!