20 Most Recent Fisher and Paykel Aquasmart wl80t65c - Page 6 Questions & Answers

If you have already tried all the logical troubleshooting tips and the Fisher and Paykel Top Loader washing machine model WA7060 is still not turning on, there may be a few potential causes:

1. Power supply issue: Check if the power outlet that the washing machine is connected to is working correctly. You can test the outlet with another appliance or device. If the outlet is not working, you may need to call an electrician to fix it.
2. Control module or power board failure: If the power supply is not the issue, then there may be a problem with the control module or power board of the washing machine. In this case, it may need to be replaced or repaired by a qualified technician.
3. Faulty power cord: The power cord may be damaged or faulty, causing the machine not to turn on. Check if the power cord is properly connected and if there are any signs of damage. If there are, replace the cord with a new one.
4. Circuit breaker tripped: Check if the circuit breaker for the washing machine has tripped. If it has, reset the breaker and try turning the machine on again.

If you have already tried all these troubleshooting steps and the washing machine is still not turning on, it is best to contact a qualified technician to diagnose and fix the issue. They will have the tools and expertise to identify the root cause of the problem and recommend the best solution.

There could be a few possible reasons for the grinding noise in your Fisher and Paykel front loader washing machine. Here are a few things to check:

1. Check the drum paddles: If the drum paddles are worn or broken, they can create a grinding noise during the wash cycle. Check to see if any of the paddles are loose or damaged.
2. Check the drum bearings: The drum bearings are responsible for supporting the drum and allowing it to spin smoothly. If they are worn or damaged, they can cause a grinding noise. To check the bearings, try spinning the drum by hand. If it makes a grinding noise or feels rough, the bearings may need to be replaced.
3. Check the drive belt: If the drive belt is loose or worn, it can cause a grinding noise. Check the belt for any signs of wear or damage, and make sure it is properly tensioned.
4. Check the motor: A faulty motor can sometimes cause a grinding noise. If you suspect the motor is the problem, it's best to call a professional for assistance.

If none of these solutions fix the problem, it's best to call a professional to diagnose and repair the issue.

If your Fisher and Paykel WA1068G1 washing machine is completely dead, it could be caused by a few different issues. Some possible causes include:

1. Power supply issue: Check to make sure that the washing machine is properly plugged in and that the outlet is functioning properly. Also, check the circuit breaker or fuse box to see if a circuit breaker has tripped or a fuse has blown.
2. Control board issue: The control board of the washing machine controls all the functions of the machine. If the control board is faulty, the machine will not turn on.
3. Faulty door lock: The door lock is an important safety feature that prevents the door from opening while the machine is running. If the door lock is faulty, the machine will not turn on.
4. Motor problem: The motor is what powers the washing machine's drum. If the motor is not working, the machine will not turn on.

It's best to consult the manual or a professional technician to diagnose the problem and recommend the appropriate course of action. Sometimes, the problem can be solved by resetting the machine or replacing a part, but in some cases the machine may need to be replaced.

It sounds like your Fisher and Paykel washing machine is displaying an error code, indicated by the beeping sound, the blinking wrench light, and the Regular and Easy Iron lights being on. The specific meaning of this error code will vary depending on the model of your washing machine, but it likely indicates a problem with the water supply. The most likely cause of the problem is a clogged inlet hose or inlet valve. The hose that connects the water supply to the washing machine can become clogged with debris, and the inlet valve can become clogged with mineral buildup. To fix this problem, check the inlet hose and valve for any clogs or debris. Another possible cause could be a malfunctioning pressure switch, which measures the water level in the machine. It could malfunction, causing the device to think that the water level is too low and stopping it from flowing in. You should consult your washing machine's user manual for the specific error code and troubleshooting steps for your model or contact the manufacturer for further assistance. It's essential to follow the manufacturer's instructions and guidelines when working on your washing machine and only attempt to repair or service it yourself if you are familiar with the product.

Firstly..unplug the unit for 2 minutes to see if it"ll reset. Otherwise, UNPLUG Open the panel & make sure the power lead is plugged firmly in to the module & the display board is plugged in to the control module. Apart from that, there is not much else you can do except call someone in to test the control module to see if it is working.

Hi, Please power cycle your washing machine by unplugging your machine for 1 minute before plugging it in again. If this issue reoccurs , then please check that there are no debris at the bottom of the washer. And you can double check whether the washer door is being shut properly. Thank you.

Either the bearings are dry and need lubricating with copper ease grease or the motor winding is open circuit and needs replacing.

Question edited for clarity and typo 'dishAwasher' ,lol. If it is tripping the breaker, it is just a dead short to earth and the most likely reason is a failed element with a hole in it. Easy fix if it is that. Six years old is nothing. Call for service or get your Digital Multimeter out. :>D

your clothes load is too heavy on one side; stop it move some around and turn it back on and see if it doesn't wobble all over.

Generally they can be repaired. If it is older than 15 years, some parts may be unavailable. https://www.google.com/search?q=Fisher+and+Paykel+Intuitive+Eco+parts ..

Contact F&P directly to inquire about a manual.

Fraudulent page blocked for your protection http://www.worksite24.com/ Fraudulent pages usually attempt to trick you into sending money with the intent of obtaining unlawful gain.

No Previous Answers given and no Previous Questions from you Liz. Click Comment under my post if you need further help. https://www.fixya.com/users/liz-anderson-62926

How to Find Your Serial/Model Number - Refrigerators

https://producthelp.fisherpaykel.com > ... > Refrigerators Jan 28, 2019 - Serial label - located inside cabinet at bottom right. RF605 & RF523 Quad Refrigerators. Serial Plate_RF605&RF523_Back of app.jpg. Serial Label ... ..

WE CAN NOT GUESS IF THE COMPANY DOES NOT KNOW

Loose or defective belt. Check pulley and try to tighten if possible or replace

Maybe you can look at the basic manual that gives you when you buy it, but if not, you can look a technical experts to check it if it has a problem... but I recommend you to not screw it, but look if there is a lock on the outside or if it is in inside, don't do anything but try to look again in you tube ( if you don't want a technical expert)