20 Most Recent
NetGear N600 Wireless Dual Band Router - Page 2 Questions & Answers
Killed my netgear modem n600 power cut mid firmware upd.plsss helpp
only suggestion is look at the bottom for the hole with the red circle and use a pen or paper clip to hold the button in there for 12 seconds (all lights should flash a couple times) hopefully its at factory defaults and working again... just need to set up from scratch.
Echolink port forwarding problem
such a complex topic and so little info!
to reach an open port you need to know a couple things
1) the ip address your trying to reach x.x.x.x
2) the port you will use :xxxxxx
and it can be put into a browser like so 71.233.23.40:8080
to make it so people can reach you is the fun and dangerous part!
things you will need:
1) your wan ip (google "what is my ip")
2) the specific device you are making available's lan ip (cmd - ipconfig /all works well on windows)
3) what port your supposed to open (i'm sure the documentation or program says somewhere)
log into your router and find the port forwarding and triggering section under advanced in a netgear (application and gaming in some others)
1)name it
2)put the number to open in twice
3)select protocol (ive usually used tcp... udp for file transfer sometimes)
4)fill in the rest of your lan ip
5)tick the box to enable and save settings
now there is a hole letting traffic on a certain port reach the named lan ip... OH, make certain that device has a static ip, if its ip changes you'll find headaches at inconvient hours.
hope i got you pointed the right way
Requiring password
If your wireless access suddenly requires a password, one of two things has happened...either you are inadvertently trying to connect to a neighbor's wireless router, or someone has modified your router. If you are certain it is your router you are attempting to connect to, and it is requiring a password you did not setup, your best bet is to perform a hard reset. There should be a reset button on the back of your router. You should press and hold this button for a few seconds. This will clear all setup information and return the router to factory setup.In order to setup your router from this point, you will need to connect directly to the router, perform whatever setup options you prefer, and then you should be able to connect wirelessly.It is highly recommended that you setup a password for wireless access. It is also recommended you change the admin password to prevent someone else from making unwanted modifications.
Wireless LAN button won't switch off.
Most Netgear routers have a recessed button on the back or bottom panel, marked "Reset" or "Restore Factory Settings". Because the button is recessed, you will require a thin tool to press it. Most people use a straightened paperclip.
- Power up the router, and wait for it to complete booting up, typically about one minute.
- Press the Reset or Restore Factory Settings button until the test or power led starts blinking. This takes about 20 seconds. Release the button.
- Wait for the router to reboot.
- Log in with the default password.
If the reset was not successful, try these additional steps AFTER the router has finished rebooting.
- Unplug the router's power.
- Press and hold the Reset button. While the button is held down, reconnect router's power.
- Continue to hold the reset button for 20 seconds after reconnecting the power.
- Wait for the router to reboot.
- Log in with the default password.
I cant find my beacon interval
Select Wireless under the Configuration tab, then select Advanced from the side menu the beacon setting should be the 3rd setting listed.The default beacon setting should be good for any setup it might help to know why you want it changed.
Recovery my password
There should be a small reset hole in the back. Hold it in till it cycles. This will clear all custom settings.
This function is not supported by the current operating system
Best option in this case (since it was once working), read and follow the instructions on the back of the router to hard reset the router (typically holding the little red reset button in for 15 seconds or more until the lights on the front flash, and so on)
Want netgear N600 to be unsecured
To unsecure your Netgear wireless router, turn off the encryption setting in the wireless settings.Connect a LAN cable from the Netgear to the LAN port on yourcomputer, open a browser and enter the Netgear configuration URL -http://192.168.0.1The default login = adminThe default PW = passwordYou can now change the default admin password and configurethe wireless settings.Go to the wireless configuration and set up the SSID and WPA or WPA2encryption or turn off the encryption..Now apply these settings to the wireless card in your laptop/computer.To secure your wireless network from unauthorized access, please click on thislink and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security
What is my default ownership password netgear N600 only numbers
See the following articles for more information:
Log in to your NETGEAR router by browsing to http://www.routerlogin.net or http://www.routerlogin.com. Enter the username (admin)and password by default the password is 1234 unless it has already been changed
hope it helps
Lost passkey to my Netgear N600 Double Band Router wndr 3400
Connect a LAN cable from the Netgear to the LAN port on yourcomputer, open a browser and enter the Netgear configuration URL -http://192.168.0.1The default login = adminThe default PW = passwordYou can now change the default admin password and configurethe wireless settings.Go to the wireless configuration and set up the SSID and WPA or WPA2encryption.or passphrase etc.Apply these settings to the wireless card in your laptop/computer.To secure your wireless network from unauthorized access, please click on thislink and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security
Not finding what you are looking for?