20 Most Recent Linksys Wireless-G WRT54GS Router (e125894) - Page 2 Questions & Answers

If you cannot access the router setup page because of invalid password , you will really receive that error message, When you try to access the router setup page try to leave the username blank and password will b admin, if that one is not working try to use your commonly use password and leave again the username blank and if still not working the next step is to reset the router by pressing the reset button for 15 seconds while the power is ON, then after that the router will be back to its default settings with the deafult password which is admin..

Hope that helps.........

Go to the linksys website at www.linksys.com, select your router, and you should find a link offering a driver download.

Hello and Welcome to FixYa!

You download the software needed to configure your Linksys wireless router from Linksys website.

If you have version 7.2 click below
http://downloads.linksysbycisco.com/downloads/WRT54G-v7.2_Setup_Wizard,0.zip

If you have version 7.0 click below
http://downloads.linksysbycisco.com/downloads/WRT54Gv7-EU_v7_00_4,0.zip

If you are not sure, try anyone.

If i was helpful, kindly do rate me.

Regards,
Waqar

To reset the Linksys back to the default settings - Press and hold the pinhole RESET button at the back of the router with the power ON for 20 secs. then release the RESET button. To connect to your wireless router, the router's wireless settings needs to be configured with the SSID, encryption etc. and also the wireless cards in all the laptops/computers needs to be configured with these router's wireless settings. Then the laptops/desktop computers can communicate with your wireless router. Connect a LAN cable from the Linksys to the LAN port on your computer. Open a browser and enter the Linksys configuration URL http://192.168.1.1 The default login = admin The default PW = admin You can protect your router by changing the default admin PW (write it down and put it in a safe place) Go to the wireless configuration and set up the SSID and WPA or WPA2 encryption to protect your wireless network and Internet from unauthorized access. Now apply these settings to the wireless card in your laptop/computer. To secure your wireless network from unauthorized access, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

your router is not compatible with your network. There are two networks, g and n. You can get a router that is compatible with both but if you have a g network and an n router they can't communicate.

Have you rebooted the computer and the Kodak. Try deleting the device in the compter and reinstalling.

TYPE 192.168.1.1 FOR ACCESS TO ROUTER SITE....BEST, GERSHON....

Check your Acer has the wireless device and driver been installed.If so then - To connect your computer to a wireless router, you click the Refresh network list, then Choose your wireless network and then click Connect to your secured Wireless Network, it will asks for a Network Key before allowing you to connect into your wireless network. This Network Key is either the WEP, or WPA or WPA2 Encryption key that is used to configure the Wireless Router. The Passphrase is an alternate way to setup the Encryption key. When you are requested for a Network Key, you can just enter the Passphrase that was used to configure the Encryption key in the wireless router. http://www.fixya.com/support/r5270415-network_password_network_address For information on securing your wireless network, configuring the wireless router and configuring the wireless card in the laptop/computer, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Normally,default username and password of Linksys router are 'admin' .orusername can be blank and password is 'admin'. I think ,you must refer to your wireless router support manual. It can vary depending on your router brand or model . You can also visit online to check model no and their default login details.

You do not have to use the cd or driver.Shutdown your PC. Unplug the power from the router and the cable modem.Wait 30 sec. then plug in the power to the cable modem, wait 30 sec. then plug the power to the router. Wait till you have "Internet" light then restart your PC. The PC should pick up an IP address and you should be able to get on-line. This is if you have a cable service provider. If you have DSL, the router needs to be configured with PPOe. I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Hi, Sweet baby,

The default username for the Linksys router is blank and password is "admin"

I hope this information allows you to resolve this issue.

If I have helped you, please help me, and rate this suggestion the highest FixYa rating. If you cannot rate this post with the highest rating, then please comment to this post and I will try to help you further.

Regards
Anand

Try the following procedure on a computer that's directly connected to one of the router ports with an ethernet cable. This procedure will not work if you're connected wirelessly. Open a web browser, such as Internet Explorer, and type in http:192.168.1.1. A window should pop up asking for a user name and a password. Don't enter a user name and type admin for the password. Hit ok. The router setup screen should come up. Click on the Wireless tab and then the Wireless Security sub-tab. You should be able to see your present wireless network security key on this screen. You can also use this screen to change the key if you want. If you want to make some changes first select the security mode you want to use. I believe WPA gives better security but I've had some trouble using it on older computers. I use WEP. I've been able to get this encryption scheme to work with all of my computers. Next select the type of encryption. I like 128 bit 26 hex digits. Next enter a pass phrase and hit generate. The pass phrase is like a password. It should now generate four 26 character keys made up of various letters and numbers. Write down the first key and make sure you've checked the 1 box for default transmit key. Save your setting and exit. You wireless network is now secure. If you try to connect to it using a wireless device you will be prompted for a security key. Depending on the operating system you're running, you may just be able to enter the pass phrase or you may need to enter the 26 character key you wrote down. You should only have to do this once for each of your wireless devices. After the first time they connect to the secured network they should automatically remember the security code. I hope this advice helps you out.

If the router is yours and you forgot the password, you can reset the router. After that you can reconfigure your network access.There is a RESET button on the back that you can press to rebootIf the router is not yours, well, you have no business trying to krack the password.

The sticker on the bottom of the router will have a symbol more than likely that looks like the 2 arrows on the top. When you are looking at the sticker that has the MAC ID, there should be one that has that symbol and is just 7-10 numbers. That should be the owner Pin it is looking for.