20 Most Recent Maytag MHWE200XW Washer - Page 9 Questions & Answers

0helpful
1answer

Replaced drain pump on maytag bravo 300 series. Machine still makes noise when starts to drain.

Is it when the washer tub is moving??
9/7/2019 3:00:44 AM • Maytag Washing... • Answered on Sep 07, 2019
0helpful
3answers

How to reset a Maytag Bravo's mct washer

Unplug it for 5 min's
8/29/2019 6:44:27 PM • Maytag Washing... • Answered on Aug 29, 2019
0helpful
1answer

Fo5 E03 error message on washer. Door will not open. I have unplugged the washer twice but did not help. Maytag front loader W0775517

If the add a garment light is off, then the washer door will unlock after the Pause/Cancel button is pressed twice. The door will not immediately unlock while the cycle is running due to a possible high-water level in the washer, high-water temperature, tumbling or spinning. It may take up to five minutes for the washer to stop spinning and draining before the door will unlock. You will hear the door click when it unlocks. or Unplug your washer from the wall outlet if none of the these steps unlocks the door. Use a T-20 Torx screwdriver to remove the three Torx-head screws along the bottom front of the washer.
  1. Pull down on the bottom panel and pull it away from the washer. Reach through the open panel and up to the door lock. Find the release ring below the locking mechanism. Pull down on the ring to unlock the door.
  2. Tip If you must manually unlock the washer door after each wash cycle your drain pump or pressure switch may have failed and would need replacing.
Hope this is helpful
8/24/2019 2:34:16 AM • Maytag Washing... • Answered on Aug 24, 2019
0helpful
1answer

My 2016 Maytag bravos XL MCT showing error code F5. Is this a simple fix?

Lid lock error. They are explained here:

https://www.searspartsdirect.com/washer-repair/error-codes/maytag-bravos-mvw-top-load-washer-error-codes.html
8/19/2019 2:36:37 AM • Maytag Washing... • Answered on Aug 19, 2019
0helpful
1answer

How to remove top of Maytag lavender 3600 aww

Remove 2 screws at bottom of front panel. Lift panel from the bottom outward. Panel will drop down and out. Remove two screws under top to remove top
8/18/2019 4:33:03 AM • Maytag Washing... • Answered on Aug 18, 2019
0helpful
3answers

Noticed today after a wash cycle that our Maytag washer had sprayed oil on the floor underneath. It has also sounded very loud, almost like a jet engine taking off during the spin cycle.

Hi Andrea, your machine has a bad tub bearing. Considering the age of your machine, you may want to consider replacing the unit. I would call your local repair company and get a quote for the repair. Hope that helps.
8/10/2019 10:09:59 PM • Maytag Washing... • Answered on Aug 10, 2019
0helpful
1answer
0helpful
1answer

Maytag neptune chime wont accept any water

check the lid or door lock to be sure it is working.
8/7/2019 5:28:12 AM • Maytag Washing... • Answered on Aug 07, 2019
0helpful
1answer

My maytag 2000 series washer model MHWE251 powers up fine but wont start when start button pressed. If I hold down tell start button it beeps 3 times but doesn't start.

Unplugging for 60 seconds good. Then after you plug back in, literally slam the lid shut (then open) 7 times. This makes the washer reset. Sounds weird, but works.
7/14/2019 8:45:51 PM • Maytag Washing... • Answered on Jul 14, 2019
0helpful
1answer

Not draining

I am unfamiliar with your machine. It is usual the tub drain is at the lowest part of the tub and the pump is below. This means if there are no blockages, a weight of water is always present at the pump impeller so a simple pump can be used and no priming is necessary Generally the arrangement of hoses, the drain and pump is so simple if there are no blockages and the pump is in good order and running, pumping is inevitable. A blockage of the drain or of the outlet hose isn't unusual...
6/28/2019 1:01:51 AM • Maytag Washing... • Answered on Jun 28, 2019
0helpful
1answer

Maytag washer Bravo Xl will not fill with water. It will then go into a LF code. I know LF means low fill but I don,tknow how fix this problem

I have a Maytag Bravos washer and it had got progressively worse with LF code often having to restart several times. Checked every thing then bought a new inlet valve assembly from McComb supply. Replaced it and it works good. Note: wires were soldered on tabs.
6/21/2019 5:20:42 PM • Maytag Washing... • Answered on Jun 21, 2019
0helpful
1answer

I have a Maytag Bravos washer model MVWX655DW1 and when it agitates it barely moves and makes a clicking sound when changing directions.

It sounds like the clutch has seized. Have a look under the machine, a telltale sign is lots of brown / black greasy marks all over the inside of the cabinet and on the floor. If the machine is still spinning but "ratchetting" on wash, it is the clutch that is not releasing.
6/10/2019 8:45:25 AM • Maytag Washing... • Answered on Jun 10, 2019
Not finding what you are looking for?
Maytag MHWE200XW Washer Logo

39 questions posted

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Jessie Goss

Level 2 Expert

162 Answers

Sheldon Dedek

Level 3 Expert

912 Answers

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Maytag Washing Machines

  • Maytag Washing Machines

Most Popular Question

maytag 2000 series shows error code f6

  • Washing Machines
Loading...