20 Most Recent Xerox WorkCentre XD100 All-In-One Laser Printer - Page 8 Questions & Answers

clean all acessable feed rollers with rubbing alcohol applied to a microfiber cloth.

You have to reinitialize the software. I will be back in a few minutes with the procedure. I have to hunt it up.

Generally all in one devices have problem with drivers!!! The main problem is communication between computer and printer!! Try to find another driver or reinstall the old ones!!!

:) No there is no switch!!! Try to get out toner cartridge shake it well!!! Turn printer on without cartridge! See the USB or LPT connection are OK!!! It's Fuser who make this problem or his sensor!! When you turn printer on he must reach 180C. Because of that printer is checking so long!

is the add toner light on if it is it will only make one copy @ a time.

That very much sounds like a driver problem.
One thing you may try first is when you get to the download page for the drivers.Select ALL on the driver page. Normally you get one selection to show up when you just click on the driver page. When you click ALL then Go and you will see more options.
There is not a Vista driver for that product if that is your operating system.
Maybe just delete the printer and re install. Something is wrong with your driver, corrupted or just not functioning correctly.
I do not have my laptop with me right now, I left it at the office with my other documentation on it.
I will look up more in the morning for you.
But this very much strikes me as a corrupt driver problem.

Sounds like 2 different things going on.
The slow warm up is normally the toner cartridge is almost out of ink but not reporting it. It is trying to set up but there is not enough ink to do so.
The jams, if the machine is making it into the machine but not exiting, then you most likely have a broken gear on the end of the heat roller in the fuser

check for a paper jam in the machine and in the paper tray, if no paper is found take out toner cartridge shake it slightly and reinstall. Also turn machine off & unplug. Let me know if you need more help.

sounds like the registration clutch is sticking, unplug machine. the reg. clutch is located in the middle of the machine, under the drum unit, it should have about 4 little gray rollers on it, @ the rear of the shaft in the back part of the machine you will see the reg. clutch. take a little bit of alcohol and pour it over the clutch and move the roller to get the toner/dirt out of the clutch. let the alcohol dry. try machine.

This could be either your drum cartridge or your fuser unit.

Take your toner cartridge out and look right up front where the drum cartridge empties 'waste toner' back into the toner cartridge.  There's a little flap there that slides back and forth on the very end.  Slide it back and see if toner is packed in there solid.  If so, vacuum it out.  Then you'll have to replace that drum.  Sometimes you can salvage them by cleaning out all the waste toner, but usually the gear in back has already stripped and it's no use.

If everything looks fine with the cartridges, it's probably the fuser.  You can buy a new one here:

http://www.acrat.com/xeroxfuser.htm

The fuser is that part of the machine that gets real hot.  If you open the right side door, it'll be right close to the top.  There are usually 4 screws holding it in place.  If you take those screws out, you should be able to hold it away from the machine while it's running (you'll have to cheat the door).  If the grinding stops as soon as you pull the fuser away, that's probably your problem.

Let me know if any of this sounds too technical.  eric AT essonline.us

If you've modified one of the trays and still encounter the same error, it's worth checking if there are any obstructions in the paper path or if the default paper type and color settings need adjustment. Remove Jammed Paper From Tray 1: First, remove any paper from the Bypass Tray. Grasp both sides of the Bypass Tray and pull it straight out of the printer. Next, pull out Tray 1 until it stops. To remove the tray, lift the front of it slightly, then pull it out of the printer. Check for any jammed paper and remove it. Also, make sure there's no crumpled paper left in the tray or jammed inside the printer. If you have Tray 2 (optional), check it as well. Insert Tray 1 back into the printer and push it all the way in. Fully insert the Bypass Tray as well. Confirm the paper settings if prompted. Try your job again. Power the Printer Off then On: Press the Power/Wake button on the printer control panel. Choose "Power Off" to turn off the printer. Wait for a few seconds, then press the Power/Wake button again to turn it back on. Retry your print job. Replace the Paper Feed Roller (if needed): If the issue persists, consider replacing the paper feed roller. Refer to your printer's documentation for instructions on how to do this. If the problem continues, contact Xerox support.

Question edited for clarity. I found this 123-315 UI Panel Communication Error N 2.2. There is help in the first link but you need to register https://www.google.com/search?q=xerox+6204+error+123-315 ..

That means there is no communication. There is a system error that is probably a fatal error. You could try updating the firmware.

Here is Xerox error code chart. Fault Code Information (xerox.com) See troubleshooting section of manual at page 148 Xerox® PrimeLink™ C9065/C9070 Printer All other relevant documents are here Documentation - PrimeLink C9065/C9070 Printer - Xerox

I would ask a friendly Xerox engineer for an OEM one.

Fault Code 062-395: Scanner Power Cable Connection Fault or power supply fault.

Error Codes and Support Web page above states: Error Description: Drive Logic Fail Solution: 1.Recycle your printer 2.Check all connections to the Engine Control Board 3.Make sure the correct firmware is installed. 4.If the error continues replace, the Engine Control Board (MCU PWB) Manual for free download at link below: Fuji Xerox Color 550 Administrator Manual Page 205

Try disabling it. 4112 / D95 families - Fault Code 077-313 : Multi-Feed Sensing Problems. First ... You have the choice to disable the Multi Feed Sensing feature on the machine if you fail to repair the problem or if you have a hard time sourcing the sensor or the board. The NVM Setting code is: 742-268.

4112 / D95 families - Fault Code 077-313 - The Parts Drop

The Parts Drop https://www.partsdrop.com > index.php > 4112-4127-d9...

Fault Code 077-313: Oversize High Capacity Feeder Fault

Xerox https://www.support.xerox.com > en-us > article Sep 21, 2015 - Fault Code 077-313: Oversize High Capacity Feeder Fault · Try these solutions · Did this help?

Error Code Xerox 4112 Error 077-313

Copytechnet https://www.copytechnet.com > ... > Xerox Sep 6, 2019 - Cause: Multi Sheet Check Sensor Actuator loose due to torsion spring disconnected from the arm. Due to improper removal of paper jam at Registration Roll. Jamming Error 077-313 and error 075 - 211 Nov 30, 2016 Xerox 4127 cp error 077-313 Sep 24, 2016 Error Code xerox 700 077-311 Jan 11, 2021 More results from www.copytechnet.com

Visit WorkCentre 7800 Series Multifunction Printer (xerox.com) and refer to page 169 (Maintenance Section)

You can't. It is hard wired in programmed memory. The reason is because most Xerox printed are supplied on a consumables deal where you have to buy toner direct at a slightly inflated price to cover the lowered lease cost of the machine. These machine also 'phone home' for interrogation..