Xerox Phaser 7300DN Laser Printer - Answered Questions & Fixed issues
Reset imaging unit life
Usually it should do it automatically once you have replaced to a New image unit.
If you are still getting that error then you will have to change the engine control board.
You can first try this tip reset the nvram from the service diag mode some errors get stuck in the NVRAM and won't get off until a reset is done in the NVRAM. Hope this helps.
Iteminconline
11/26/2013 1:33:20 AM •
Xerox Phaser...
•
Answered
on Nov 26, 2013
•
274 views
Xerox 7300 print is pixilated
This depends on what you are trying to print and with what software. Most likely, you need to choose a higher print resolution in the software before sending to the printer, but more details would be required to give a precise response.
5/5/2013 3:11:30 AM •
Xerox Phaser...
•
Answered
on May 05, 2013
•
54 views
Changing resolution
You set the resolution in the printer driver before sending the data to the printer. Exactly where this will be will depend on which OS you are using and which software / driver you have installed.
5/5/2013 3:06:10 AM •
Xerox Phaser...
•
Answered
on May 05, 2013
•
47 views
Colour misregistration mystery
Various possible causes - the most likely are :1. Dirty registration sensors - remove IUs and transfer unit and inspect / clean sensors.2. Damages / worn IU drive gears - inspect. Replacing the gears isn't a small job, if this is your problem.3. Faulty colour registration shutter - you can check this is working in the service diagnostics menu.4. EEPROM problem on the controller board - replace main controller board.These are in order of likeliness. For further information, take a look
here.
5/5/2013 3:02:07 AM •
Xerox Phaser...
•
Answered
on May 05, 2013
•
142 views
Error u26 phaser 7300
U26 is Yellow Image Unit failure. It may be that the contacts are dirty - spilled toner?? Give it all a thorough clean, especially where the electrical contacts are - if still no luck, then a new yellow IU should solve the issue.
5/5/2013 2:47:10 AM •
Xerox Phaser...
•
Answered
on May 05, 2013
•
126 views
Phaser 7300 error message...
The problem is a crazy design in the printer itself! I've now found a reliable fix for this problem which is relatively easy to carry out. You will find the details of how to do it here :
www.michelsplace
5/5/2013 1:24:54 AM •
Xerox Phaser...
•
Answered
on May 05, 2013
•
1,704 views
What does the flashing orange light mean on my
The flashing light indicates a warning state - such as low toner - but it will not stop the printer working, so there must be more than one issue if it is not printing at all. A flashing orange will be accompanied by a message on the screen to indicate which item(s) is/are in a low state.
8/8/2012 12:20:42 PM •
Xerox Phaser...
•
Answered
on Aug 08, 2012
•
366 views
We have a Phaser 7300N that will intermittently
These are 2 different problems. The fusing issue is that the fuser roller is controlled by the "ATC Anvil calibration". This requires Transparencies (PN 42527801) to be run through the Manual feeder. You may need a technician for that, or buy a manual
The "reseat message" is probably a warping "top cover inner frame" 116-1548-00. You might need to replace that whole top.
Whit
Item, Inc.
8/8/2012 11:55:58 AM •
Xerox Phaser...
•
Answered
on Aug 08, 2012
•
171 views
Changing toner cartridges
You can reset the counter using the service menu. You can find full details of how to do this on my website
here.This will solve your problem.
8/8/2012 11:40:05 AM •
Xerox Phaser...
•
Answered
on Aug 08, 2012
•
39 views
Just downloaded latest OSX driver
I would choose DT, then you'll have the duplex function in the driver. The DT is the same as the DN, but has an extra paper tray.
2/22/2012 9:34:33 AM •
Xerox Phaser...
•
Answered
on Feb 22, 2012
•
86 views
Hi can you tell me
Yes, this can be done - it's a relatively simple process. Take a look
here where you'll find all you need to know about doing it, plus a load of other useful information about this printer.
2/22/2012 9:31:06 AM •
Xerox Phaser...
•
Answered
on Feb 22, 2012
•
59 views
Reset imaging unit xerox 7300
You can reset the imaging unit in two ways - either with a fuse, which will return the count to 100%, or in the hidden menu, which will not get you all the way to 100%. You'll find all the details about how to do it, and a lot more information about this printer
here.
2/22/2012 9:23:59 AM •
Xerox Phaser...
•
Answered
on Feb 22, 2012
•
1,072 views
I have a xerox phaser
This is a common issue with the 7300. You can read all the details, including possible solutions
here.
12/10/2011 12:28:00 PM •
Xerox Phaser...
•
Answered
on Dec 10, 2011
•
235 views
Not finding what you are looking for?