I suggest You Go to Official Xerox Printer Page For You Xerox Printer Problem On Below Xerox forum URL Link: Clearing Paper Jams In Case You Still face Problem and Need Online Assistance Then Please Follow Us For On :
Xerox Printer Support
Magenta toner(s) not being recognized, I looked into the little slot on printer where chip slides in and found one of the four contacts was bent up out of position. Rather than risk further damage by poking it in such a confined space I am going to remove the part first.
rror codes
If the printer's front panel displays a message Error XX, find the error code in this table and follow the instructions for resolving the problem. If problems persist, check the Xerox web site www2.tek.com/TekSMART/ or contact service.
ErrorUser Corrective ActionError 01
Remove and re-install the black Toner Cartridge, then turn the printer off and on.
Replace the black Toner Cartridge, then turn the printer off and on.
Error 02
Remove and re-install the cyan Toner Cartridge, then turn the printer off and on.
Replace the cyan Toner Cartridge, then turn the printer off and on.
Error 03
Remove and re-install the magenta Toner Cartridge, then turn the printer off and on.
Replace the magenta Toner Cartridge, then turn the printer off and on.
Error 04
Remove and re-install the yellow Toner Cartridge, then turn the printer off and on.
Replace the yellow Toner Cartridge, then turn the printer off and on.
Error 05, 10,11,12, and 13
Turn the printer power off, then on.
Error 20
Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
Remove and re-install the Main Charge Grid. Turn the printer off, then on.
Remove and re-install the Transfer Kit. Turn the printer off, then on.
Remove and re-install each of the Toner Cartridges. Turn the printer off, then on.
Replace the Main Charge Grid. Turn the printer off, then on.
Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
Replace the Transfer Kit. Turn the printer off, then on.
Replace the Toner Cartridges. Turn the printer off, then on.
Error 21,22,30,and 32
Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
Check for jammed paper throughout the paper path (especially in paper feeder).
Remove and re-install the paper feeder and Transfer Kit. Turn the printer off, then on.
Error 40,41,42,and 43
Check for jammed paper in the Fuser. Re-install the Fuser. Turn the printer off, then on.
Make sure that you have the correct Fuser for your local printer power supply:
110-Volt Fuser Part Number 016-1839-00
220-Volt Fuser Part Number 016-1840-00
Replace the Fuser. Turn the printer off, then on.
Error 50,51
Turn the printer off, then on.
Error 52
Remove the Duplex Unit (if installed).
Check for paper under the Upper Tray.
Turn power off, then on.
Error 53
Open left door and remove any jammed media.
Tun the printer off, then on.
Error 60
Remove the media from the Multi-Purpose Tray. Turn the printer off, then on.
Reinstall the media. Make sure you do not overfill the tray.
Error 61
Remove and re-install each Toner Cartridge. Turn the printer off, then on.
Replace each Toner Cartridge. Turn the printer off, then on.
Error 62
Check for jammed paper throughout the paper path (especially in the paper feeder and Fuser).
Remove and re-install the Fuser. Turn the printer off, then on.
Slide out and re-insert the paper feeder. Turn the printer off, then on.
Replace the Fuser. Turn the printer off, then on.
Error 63
Remove and re-install the Imaging Unit. Turn the printer off, then on.
Replace the Imaging Unit. Turn the printer off, then on.
Error 70,71, and72
Turn the printer off, then on.
Error 73
Remove and re-install the Imaging Unit. Turn the printer off, then on.
Replace the Imaging Unit. Turn the printer off, then on.
Error 74
Remove and re-install the Fuser. Turn the printer off, then on.
Replace the Fuser. Turn the printer off, then on.
Error 80,81,82,83, and 84
Make sure that all four toner cartridges are installed in the printer.
Turn the printer off, then on.
Error 01p through
Error 47p
Make sure that installed memory DIMM(s) are compatible with printer's image processor board and that they are installed in the proper slot(s).
? 0:55www.youtube.com/watch?v=Ef0WwaTXgtQOct 6, 2010 - Uploaded by natasmanda01
Cancelamento dos codigos de erros c6000, c6400 e c6020 da kyocera ... HOW TO RESET AND HARD RESET KYOCERA HYDRO XTRM ...
Today we will be replacing a Xerox Phaser 7800 transfer roller part# 108R01053
You will have to replace the fuser if you are getting the following errors:
Repeating spots or lines every "54mm" or "2.13 in"
The image quality is very light and missing a lot of color
If the control panel display reads end of life