20 Most Recent Microsoft Broadband Networking MN-100 Wired Base Station (M51-00001) Router Questions & Answers


That is a question for you to pose to your new service provider.

Microsoft... | Answered on Sep 09, 2017


Read this help file from the talktalk website.
Connecting my Windows 7 PC TalkTalk Help

Microsoft... | Answered on Mar 20, 2015


All electronic devices will eventually fail, depending on how well they are manufactured and the conditions they are operated under.
Things that will lower the lifespan of a router : high sustained amounts of traffic, being crammed into a tight space where they do not have room to remain cool, poor power, spikes or brownouts can be very damaging to routers. I would suggest making sure it is plugged into a proper surge protector in a well ventilated area.
That said, 5 years is a decent lifespan for such a device, most manufacturers will only warranty such devices for 1 year.
hope this was helpful.

Microsoft... | Answered on May 30, 2011


Please check your DNS entry is present or not in your router.

Microsoft... | Answered on Mar 30, 2010


You might try re-setting MN-100 router back to the default setting. Do this by ... look in the back, there is a small hole at one of the ends. I have mine standing up and the (small) hole is at the top. Which you can use a straighten out paper clip and lightly push it in the hole to re-set. The trick to it - is that you have to hold it for a little bit of time. I'm not sure what the time figure is, 5 or 10 seconds something like that ... but the lights on the front will start to blink. Look in you manual, it will show you where the hole is.

Microsoft... | Answered on Sep 17, 2009


To enter the router, type the gateway IP(i.e. in command prompt) by entering xxx.xxx.xxx.xxx in the RUN command . It will open a log in for your router. Default ID is admin & password is admin to. After that change the setting as desired by you, but be careful and for backup you could be in touch with your ISP's customer support exec....sodeep

Microsoft... | Answered on Sep 17, 2009


YOUR ROUTER IS NOT COMPATIBLE WITH VISTA NO WORK AROUND OR FIRMWARE UPDATE WILL WORK.REPLACE.RICHARDM69

Microsoft... | Answered on Feb 22, 2009


Hi,
as far as the game works perfectly online, i dont think you should worry...
the reason you got that message could mean that it assumes you have NAT enabled..!!
so chill and game on..!!!

Microsoft... | Answered on Jan 29, 2009


Yes, that is possible. Since you have changed providers, you have to reconfigure the router depending on your new provider.

You can try these steps:

1. Turn off the the router, modem and the computer.
2. Wait for 30 seconds then turn on the modem and make sure that all (if not most) lights are stabilize
3. When the lights are stabilized, turn on the router and wait for the lights to stabilize.
4. When both the router and the modem are stabilized, you can turn on the computer and check for the connection.

If it still does not work, you may need to configure the router based on the settings needed by the service provider that you have. If you wish, inform me of the name of your service provider and I will give you the specific settings on how to configure your router.

Microsoft... | Answered on Oct 01, 2008


Hi again,

Sorry it took some time to get back to you. Apparently no, it would seem that each console would need separate IP address from the ISP not only from the router. But then again, that would sound logical since the router make both console appear as one to the ISP which of course would not do.

Microsoft... | Answered on Jul 15, 2008


Delete any unimportant emails. You can start by removing the ones with large attachments. Those tend to hog lots of space.

Microsoft... | Answered on Jun 16, 2008


router do not require software unless this is a usb version.

Microsoft... | Answered on Jun 07, 2008


Hi again XX,

Personally, have not tried game console(s) online, but my kids have. Will ask them and relay info. Should not really be a problem I think, I dont hear any issue from any of them.

Microsoft... | Answered on May 25, 2008


Hi,

To my knowledge, yes. "dial-up internet" connotes standard modem attached to a computer unlike DSL modems (non USB) that are stand alone. Therefore the dial-up internet modem should be connected to a single computer. That PC then would have to enable its Internet Sharing for others in the network to access the Internet. This is accomplished by hooking all the PCs to a single network using a hub/switch. The router can perform this function (hub), however, all the PCs in the network would have to use for their Default Gateway IP address not that of the router but that of the PC with the dial-up internet modem. Having said that, it would then be necessary to use static IP adds in all the PCs. The built-in firewall and DHCP features of the router would not be necessary.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Microsoft... | Answered on May 23, 2008


Sorry, routers are not my area of expertise. Please try a different expert..Benimur if possible. He's good with this stuff.. or even Ekse.

Microsoft... | Answered on May 16, 2008


To resolve this issue, turn off Internet Connection Sharing on your network connection: 1. Click Start, click Control Panel, and then double-click Network Connections. 2. Click your network connection, and then under Network Tasks, click Change settings of this connection. 3. On the Advanced tab, clear the Allow other network users to connect through this computer's Internet connection check box. 4. Click OK. 5. Restart your computer.

Microsoft... | Answered on Feb 16, 2006


To resolve this issue, remove the network bridge. To do so, follow these steps: 1. Click Start, and then click My Network Places. 2. In the left pane, click View Network Connections. 3. Look for any connection that is bridged. 4. Right-click the bridged connection, and then click Remove From Bridge. 5. Repeat step 4 for each connection that is connected with a bridge. 6. When the bridge is removed from each network adapter, right-click Network Bridge, and then click Delete. 7. Click OK. When the all the bridged connections and the network bridge are removed, the broadband hardware is automatically detected.

Microsoft... | Answered on Feb 16, 2006

Not finding what you are looking for?
Microsoft Broadband Networking MN-100 Wired Base Station (M51-00001) Router Logo

33 questions posted

Ask a Question

Usually answered in minutes!

Top Microsoft Computers & Internet Experts

Ekse

Level 3 Expert

13434 Answers

ThaMp3Doctor
ThaMp3Doctor

Level 3 Expert

8597 Answers

Scoee Scoffer

Level 2 Expert

162 Answers

Are you a Microsoft Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Microsoft Computers & Internet

  • Microsoft Computers & Internet

Most Popular Question

good people bought

  • Computers & Internet
Loading...