20 Most Recent Packard Bell iMedia SL 9553 (P660401806) PC Desktop Questions & Answers


Have you had a look at the condition of the thermal paste?

Packard Bell... | Answered on Nov 04, 2017


Have you checked the wall socet has power and is turned on? have you checked the power cable?

Packard Bell... | Answered on Aug 02, 2016


You don't. The WPS button is on the router. Press it and, when the latop sees the wireless network, it will ask you to enter the pin. The pin is normally writen on the sideor bottom of the router on a sticker.

Packard Bell... | Answered on Aug 02, 2016


sounds like its shorting out try another usb port and or new cable

Packard Bell... | Answered on Jan 29, 2014


This answer is not an answer to the question. FixYa should demonstrate it cares what it posted on its site by removing spam posts like one advising that a full restore operation is the answer. Clearly, Khalil has not read the question.

Packard Bell... | Answered on Sep 15, 2013


What happens when you try?

Packard Bell... | Answered on Aug 26, 2013


WARNING: Before you start troubleshooting remember that you are dealing with electricity that can KILL. http://www.kitchentablecomputers.com/static.php - rules Test all power and data leads that attach to your hard drive IDE,SATA the leads from your (motherboard to your hard drive) make sure they have secure dust free connections and are not faulty if its a 40 pin flat ribbon type it will be the first to fail make sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure connections and are not faulty even something as small as a faulty electrical fan and its lead can cause you problems computers need all power and data to continue through every working device and to have an end so any faulty leads will end up with a computer error Check your RAM. The RAM is located in the middle of the motherboard. There are tabs that you can push to release the RAM. Remove it and put it back in place until the tabs pop out. Loose RAM can cause your computer not to start properly where you want to see a video signal.

Make sure your graphics card is securely seated with no dust built up or in the socket if you remove your graphics check the socket to make sure its dust free Restart your computer then reinstall it this should activate found new hardware wizard Check the vga lead for secure dust free connection or try another vga lead.

Packard Bell... | Answered on Feb 08, 2013


It is battery on your motherboard that keeps alive basic computer settings including the clock. Removing the battery will reset all the settings in BIOS to default.

Packard Bell... | Answered on Feb 08, 2013


No wireless on this model if specs are correct.
http://reviews.cnet.com/desktops/packard-bell-imedia-sl/4507-3118_7-30065730.html


Desktops that have wireless may not have a wireless button. Just part of the OS. A button is a convenience on laptops, but not required.

Packard Bell... | Answered on Nov 09, 2012


Just make sure all the cables are connected properly.

Still need help ?

Comment!

Packard Bell... | Answered on Jun 26, 2011


A beep code usually means there is a problem with the motherboard, CPU or some other hardware. You have to listen carefully to the code, write it down if necessary,ie: one long, two short, etc. and refer to your manual. Alot of times it's a ram problem,ie, either one stick is bad or maybe there is a bad connection. Write down your beep code and repost.
Dave

Packard Bell... | Answered on Jun 20, 2011


Check the pins if it's a PS2 mouse. They sometimes get smashed together. Try another mouse by removing the bad one first in Control panel Mouse or pointing device, remove or uninstall. reboot and put in new mouse. should be found by software and installed correctly.

Packard Bell... | Answered on May 02, 2011


No power and power LED does not light up, this indicates either the mains power is off or you have a faulty power lead. Test the mains socket and the mains power lead.
If these are OK then the fault most likely a faulty switch mode power supply. Remove the switch mode power supply and get it tested at your friendly computer repair shop OR borrow a power supply and insert it into your PC to see if it now boots up.
If it boots up the replace the power supply with a new switch mode power supply with the same total wattage or higher wattage.

Packard Bell... | Answered on Apr 01, 2011


Hi i'm Basti,

How bout the fan for your power supply, is it running? Try to retrace the cables to motherboard and make sure its tight. Change or use another power supply if possible.


Keep me posted. Hope this helps.

Packard Bell... | Answered on Feb 25, 2011


YES YOU WOULD BE ABLE TO Call packard bell and show them proof of purchaase and get them sent out to you now packard bell was bought out by hewit packard and there number is or you could go to this website and get any driver you would need http://list.driverguide.com/list/company788/

Packard Bell... | Answered on Jan 14, 2011


You can purchase the battery at any Radio Shack, the number should be CR2032

Packard Bell... | Answered on Jan 13, 2011

Not finding what you are looking for?
Packard Bell iMedia SL 9553 (P660401806) PC Desktop Logo

Popular Tags

84 questions posted

Ask a Question

Usually answered in minutes!

Top Packard Bell Computers & Internet Experts

Lee Hodgson
Lee Hodgson

Level 3 Expert

4810 Answers

Gustavo Ortiz
Gustavo Ortiz

Level 3 Expert

637 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Packard Bell Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

iMedia Packard Bell

  • iMedia Packard Bell

Most Popular Question

keeps beeping when turn but no

  • Computers & Internet
Loading...