Top 20 Gaggia Brera Coffee Maker Questions & Answers

If there is no external brew temperature adjustment, there may be an internal one that has failed.

I think that you button doesn't make a good contact. Try to press it with different pressure and on different sides slightly off center to give this a try - it may be just a bad contact that is enough to change the bean setting but not enough to reset the warning indicator through a long press. Let me know how it goes ... they may have changed the button that needs to be pressed as well (does your manual say anything different?)

Carefully check soldered joints and re solder any suspect cracked,cold, bad joints. "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

close the steamer valve

You may have accidentally changed the amount setting for your espresso shot when resetting the descale counter.If you lost the manual you can find one here. http://www.gaggia-usa.com/support_docs/Gaggia_Brera_Quickstart_Guide.pdfOn page 11 (with the printed number 31) you find how to change these settings:• Place a cup under the dispensing spout.• Hold the "espresso size" button pressed for 5 seconds to enter the programming mode; the "coffee" icon will blink quickly and the coffee will start to be brewed; the icon will flash during the whole coffee brewing cycle.• Press the same "espresso size" button again when the amount of coffee in the cup reaches the desired level.At this point the button "espresso size" is programmed; each time it is pressed and released, the machine will brew the same amount of coffee that was just programmed.The same operation can be repeated for the "Lungo size" button.

hi,when you have the warning lights blinking it may you have a faulty micro switches you have one for the brewer one for the door and one for the basket or faulty boiler not heating up

try to hold the steam/hotwater button for 5-6 seconds.

You have to reset this manually after descaling. This is done by pressing the bean selector button for 6 seconds.

Hi there My experience tells me that when a red light flashes on a coffeemaker it is one of three things: It needs water to be able to make more coffee The "bowl" that the compressed coffee goes in ids full and needs emptying It needs cleaning I would start filling the waterholder, Then emptying the compressed coffee holder If neither works, then start the cleaning prosess Best of luck and enjoy your coffee Kolbrun

If you close the machine without the brew unit inside, the gears aren't aligned anymore. I tried to put the machine off and then back on. You can hear the gears turn. After a couple of repeats, I was able to put the brew unit back inside.

finer grind setting and non oily beans did the trick for me.......

Hello, are you turning to the selection knob back to its central position? once you do this the and the unit warms up the triangle should disappear

The icons displayed blink slowly to

show that the machine is warming

up.

When warm-up is complete,

the machine performs a rinse

cycle of the internal circuits.

During this phase, the icons displayed will blink in sequence.

• When the operations described above

are completed, the icons on the display

will illuminate.

The display will appear as

shown to the side. The displayed

aroma is the factory setting

when the machine is switch on for

the fi rst time, or it is the same as the

aroma that was selected for the last

brewed coff ee.

The machine is then ready to brew beverages if you have any further questions or the triangle does not go away please message me back for further diagnosis Thank youRick

If the frother is warming the milk, but is not frothing, then you want to make sure the panarello is clean.

Slide the cover off the frother and check the pin hold on the top edge of the cover. If this hole is blocked the milk will not froth. Rinza is great clean to help prevent these issues. http://www.cerinicoffee.com/rinza_urnex.asp

Also recommend frothing water instead of milk to clean the frother well.

For more information visit: http://www.cerinicoffee.com/Coffee_cleaning_supplies.asp

Question translated from German. We are a north American website and only speak English. Electro Tanya has a circuit diagram, but there is nothing else. https://www.google.com/search?q=gaggia+syncrony+logic+service+manual ..

It looks like the Triangle is the problem section, not that I understand why. These machine need servicing every 9 to 12 months if you use them every day. https://www.manualslib.com/manual/1069719/Gaggia-Brera.html?page=23#manual Videos https://www.google.com/search?q=Gaggia+Brera+can%27t+run+test+mode ..

Tanya has it https://elektrotanya.com/gaggia_syncrony_compact_digital.pdf/download.html more her but only User manual. https://www.google.com/search?q=gaggia+syncrony+logic+service+manual

It seems to be a strange make model combination. Gaggia is the maker, Costa Coffee is a shop franchise, no Lama or even Llamas :>D Videos that should help. Strangely, the most common reason for burrs seizing is small stones the size of a coffee bean that get through production, nicely roasted and covered in coffee oils. https://www.google.com/search?q=Costa+Gaggia+LAMA++A+coffee+grinder+strip+and+clean ..

The manual is next to useless. I would find the closest Gaggia Service Centre and ask them to diagnose and fix. It says it needs descaling every 2 weeks, but you have a blockage in a water valve somewhere.https://wiki.wholelattelove.com/Gaggia_Syncrony_Logic#Descalinghttps://www.google.com/search?q=gaggia+syncrony+logic+rs+descale+heater+coil..