Top 20 Sony Cyber-Shot DSC-W570 Digital Camera Questions & Answers

hi, check the battery's shape, if it is bulged replace it, check the panel keys if any of it sticky or loose, use contact cleaner spry on the keys.

Sure your battery has enough power to charge the flash? charge the battery and try again.

Short answer, No. The potassium in a banana is not in the same concentration nor is it purified. It is similar to how karoseen come from crude oil. a match in the oil will simply go out. The karoseen on the other hand will burst into flames.

Dry your phone with simple towel. Then put your phone in a bag of rice for over 24 hours. Take out your phone and try to start it and see if it works. I am talking about phones in which battery can't be separated. If you could separate the battery then, dry it from outside then pull out the battery and dry gently inside then put it in a bag of rice overnight and start it next day.

Good luck!

If the battery can come out, pull it immediately to prevent further electrical and corrosion issues. If it landed in dirty water, you should rinse it off as it is already wet it won't hurt anything further. After that there are a few options but the main goal it to be sure you get it all the way dry before turning it on again. The last time my phone went in the water I put it in an OPEN ziplock bag full of rice then placed it by the heater. If you are like me and it is hot enough in your house, you could turn your oven to it's lowest setting, 150 degrees or less, and leave your item in there for an hour or more. I would not turn it back on for at least a day or two. if you see and steam on the inside of the screen, it is not dry enough to turn on.

I suggest you open up the unit as much as possible, then pack it in rice about 2 inches deep all around it in a box and let it sit for at least a week. The rice is good for drawing out moisture from anything. Russ

Try cleaning the card contacts...

the flash light works only on low light environment, check your setup manu, change the setting to always flash if you need.

If it is a SD or SDHC memory card, there is a small write protect switch on the side of the card. Remove the memory card from the camera and slide the switch to the unlocked position.

Has it been dropped? I had a cabera that was dropped and the lense would not go all the way back in which caused the lense covers to not close.

The date and time (and a lot more) are automatically stored with every picture in its EXIF metadata. Any photo viewing/editing program should be able to display this data. To print this data, please consult the documentation for whatever program you're using to print your pictures. Depending on the program and printer you may print the date on the image, in the margins, or on the back.

The date and time (and a lot more) are stored with every picture in its EXIF metadata. Any photo viewing/editing program should be able to display this data. To print this data, please consult the documentation for whatever program you're using to print your pictures. Depending on the program and printer you may print the date on the image, in the margins, or on the back.

Try these procedures.

Take a look at this.

If you haven't done anything to the memory stick since then, you may be able to recover at least some of the pictures. Do a Google search for "data recovery software" and select a program appropriate for your computer and operating system. Put the memory stick into a card reader attached to your computer and run the program.

SD and SDHC cards have a slide switch along one edge. The position farthest from the metal contacts locks the card, protecting it from writes. The position nearest the contacts unlocks the card.

Press the MENU button. Select the toolbox icon. Select the wrench-and-hammer icon. Select the second item on the menu.

Hi there:I suggest check EV setting is on the + side and not neutral (0). Either that or Image Adjustment setting is wrong. Check EV by pressing the +/- button (right side near On/Off switch). Hold EV selector and make sure 0.0 is in the display.Hope this helps.

The date and time (and a lot more) are stored with every picture in its EXIF metadata. Please refer to the documentation for whatever program you're using to print. Depending on the program and printer, you may print the date on the image, in the margins, or on the back.

You might try removing the battery for a minute or two to reset the camera. You may lose any special settings in the process. After reinstalling the battery, try turning the power on and off again.