Audiovox AVP7000 VCR - Answered Questions & Fixed issues

take a hair dryer on low setting and try to blow warm air into the vcr to warm it up until light goes out

hello eckert2407!
guess this vcr has autotracking, so no buttons.
regards

Check for any screws to be loosened that attach them together.

I am looking forward to my boosted rating from you!

Solution: The tape not spooling back into the cassette is caused by a fault with the idler or clutch mechanisms. There are usually felt clutches associated with the idler gear and felt clutches on the take up and supply reels. On many VCR's the idler gear engages a direct drive gear for FF & FR, whereas for cue & review the idler gear engages a gear that drives the spool via a felt clutch, the same gear that is used for play. During play, however, the capstan/pinch roller pulls the tape through the mechanism with the take up reel pulling in the slack tape. Check for a slipping felt clutch mechanism. A little trick that works well, remove the offending spool and most spools can be popped apart, use some violin bow resin and carefully work the resin into the felt. You will find that the resin restores the lost grip of the felt with lasting results. Violin resin can also be dissolved into alcohol to provide a gloss finish over reworked solder joints.

That is 'dew' as in wet. Do you have it in a warm, dry location? This time of year they can attract condensation if the VCR is in a cold place.
Hope Ya Fix it!

It's possible that the issue with your Audiovox pursuit PRO9056c remote start system is related to the antenna or its connection. Here are a few things you can try to troubleshoot the issue:

1. Check the antenna connection: Make sure the antenna is properly connected to the control module of the remote start system. You may need to remove the panel where the antenna is mounted to access the wiring and connections. Check the wiring for any signs of damage or corrosion, and make sure the connections are tight.
2. Check the fuse: The remote start system may have a fuse that is responsible for powering the antenna. Check the fuse to make sure it is not blown or damaged.
3. Reset the system: Try resetting the remote start system by disconnecting the battery for a few minutes, then reconnecting it. This may help reset the system and resolve any issues that were causing it to malfunction.
4. Consult a professional: If you are not familiar with automotive electronics or are unable to resolve the issue with the above steps, it may be best to consult with a professional technician who can diagnose and repair the system for you.

It's also possible that there is a problem with the remote start system itself, such as a malfunctioning control module

See if the videos and articles help. https://www.google.com/search?q=connect+a+Roku+2+to+an+Audiovox+ADV12 ..

Unfortunately, you are probably dealing with a copy protection issue. The digital handshake can't be returned by your KLV3913. You get the same issue if you connect a HDMI source (Blu-ray player) to a VGA monitor. I wish that I had better news for you. Cindy Wells

It's all one board, chances are your audio output IC has failed and needs replacing

Jim, First thing I would do is try a different DVD to see if the problem persists. Otherwise, this device is equipped with integrated speakers, meaning it is unlikely that you will be able to replace them. You may be in the market for a new Audiovox, unfortunately; but before you scrap it I suggest taking it to a local electronic repair store near you. Hope this helps, Best regards

I I had a similar problem. What worked for me, was resetting the player. By pressing the picture button on the player itself three or four times I got to the reset option. Press play when it says press ok to reset. My remote automatically started working at that point. Hope this works for you

are you using the right remote, one time i tried to change things and come to find out it was on the dvd not the tv

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. The site has set-up code list & set-up procedure to many popular brand remote controls. The site has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Set-up code list to many brand remote controls also is given. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily. http://homenol.blogspot.com/ http://remotesearch.blogspot.com/ http://electronicshelponline.blogspot.com/ http://electrohelponline.blogspot.com/ Programming Notes • If your device does not respond to the remote after trying all codes listed or your brand is not listed in the code list, use the Auto Code Search method to program your remote. • Sometimes the first code that "works" with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality. This is a trial and error procedure; and quiet time consuming. You might have to check different codes said for your device

first, make sure the TV in in American Cable mode (ntsc). next do this, menu... tuner... cable... scan... the reason maybe the TV is on TV air mode; but now is receiving cable. from the antenna coax cable. . another reason is that many cableco's now use Switched Digital Video ( a more robust setup) that now requires the Digital Tuning Adapter... also to help prevent free-loading. a last possibility is your (old) TV does Not work on the new cable. A new TV usually cures this ...!

Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Try with an other known good Cd. If it too beaves so, the laser pickup unit inside the set is faulty. Check and replace it. If you wish to get some details; visit the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ http://homenol.blogspot.com/

There are "universal" remotes available that can be programed to different electronic equipment. Just make sure that your model and brand is listed with the codes.

try this link i think it could be the first one on the page. manual for Audiovox PLV16081W 8 LCD television Google Search

try rebooting phone by turning off and then on

There is a decoding chip for surround sound. If it goes bad all you get is stereo. Happened to me with my Pioneer receiver.