20 Most Recent Cobra 25 LTD 40-Channels Base CB Radio Questions & Answers

0helpful
1answer

Have got a es 880

Got a es880 echo chamber cybernet wirerd i want to wier to my super star 3900crt whats the wiering code help please thanks Tom
3/11/2018 1:38:06 PM • Cobra 25 LTD... • Answered on Mar 11, 2018
0helpful
1answer
0helpful
1answer

Cobra 25 ltd wx classic

the mics on these cobras have a receive wire in them so the transmit will still work even if the receive wire is broken,if this wire is broken the unit will not make any sound...........remove the plug from the radio end of the mic and check the connections on the 5 pin connector.....(could be a cold solder or broken wire) or try a new mic or one that is proven work on another radio
hope this helps.................good luck!
4/21/2017 3:40:40 PM • Cobra 25 LTD... • Answered on Apr 21, 2017
0helpful
1answer

I have a nighthawk cobra 25 LTD 40 channel,How do i get the luminated back light to work.

you must have great knowledge of CB'S to tackle this problem.
9/13/2015 9:56:04 PM • Cobra 25 LTD... • Answered on Sep 13, 2015
0helpful
1answer

What is the wiring diagram for realistic 211173 mic to cobra 25ltd

first,a realistic plug is a 5 pin D.I.N. type and a cobra 25 is a 4 pin screw on . If you are trying to save $$ by using an old mic then let me say that you can get them prewired real cheap.
7/16/2015 6:31:42 PM • Cobra 25 LTD... • Answered on Jul 16, 2015
0helpful
1answer

COBRA 25 LTD spikes without keying mike

buy a different cobra 25 4 pin mic and try that . If that doesn't work than you inherited a piece of junk .
2/16/2015 12:51:25 AM • Cobra 25 LTD... • Answered on Feb 16, 2015
0helpful
1answer

Blown fuses

no need for wiring diagram just replace the reverse polarity diode. Look at where the power wires come into the radio and you will see a diode. that's the one to change.it should be a 1n4001
2/16/2015 12:40:00 AM • Cobra 25 LTD... • Answered on Feb 16, 2015
0helpful
1answer

How to increase the receive on a cobra 25ltd classic

1,if your antenna is not properly tuned you may be loosing receive as well as power 2,how your swr? 3 you may want to purchase a little driver with a built in receive amp.
2/2/2015 6:23:22 PM • Cobra 25 LTD... • Answered on Feb 02, 2015
0helpful
1answer

25 ltd classic 1992 china

L 19 is the adjustment can for the N/B . If you choose to adjust it then turn it a little at a time. If it still doesn't work right then let a tech take care of it.
12/22/2014 12:38:22 AM • Cobra 25 LTD... • Answered on Dec 22, 2014
0helpful
1answer

Cobra 25 has no modulation

sounds like a voltage problem that you are incapable of handling. Take it to a tech.
12/22/2014 12:25:45 AM • Cobra 25 LTD... • Answered on Dec 22, 2014
0helpful
1answer

My cb dosent transmit

did you play around on the inside of the radio???
12/22/2014 12:12:38 AM • Cobra 25 LTD... • Answered on Dec 22, 2014
0helpful
1answer

Cobra 25 ltd will not transmit it will on pa mode

there is the problem. a $150 repair bill for a $ 25.00 problem. After you put in this new IC did you put it on a scope to check it out.How about a frequency counter to make sure you were on the right frequency? take it to a tech and let him fix it .
12/22/2014 12:11:58 AM • Cobra 25 LTD... • Answered on Dec 22, 2014
0helpful
1answer

How do I test a cb to see if it is working

turn it on
12/1/2014 12:18:31 PM • Cobra 25 LTD... • Answered on Dec 01, 2014
0helpful
1answer

How do i adjust dead key on a cobra 25 ltd classic cb

The only "adjustment" is the AM POWER trimmer. Lowering this will lower your dead key but will also lower your "swing" power. the TX circuit must be modified to lower the dead key and maintain full output. there are many articles on the web for such modification.
11/25/2014 11:51:29 PM • Cobra 25 LTD... • Answered on Nov 25, 2014
0helpful
1answer

Adjust modulation pot

VR5
11/25/2014 11:39:55 PM • Cobra 25 LTD... • Answered on Nov 25, 2014
0helpful
1answer
0helpful
1answer

Cobra 29 ltd jumps channel why

not on frequency, take it to a tech.
11/25/2014 8:01:35 PM • Cobra 25 LTD... • Answered on Nov 25, 2014
0helpful
1answer

Cobra 29 ltd classic no modulation

check VR4 to make sure it isn't closed . Check D 11 to make sure it isn't clipped . Turn VR 4 clockwise till it stops then back it off a little .If D 11 is clipped replace it with another diode then try it again. If it doesn't work it could be your final or your driver so replace both..
11/25/2014 7:04:26 PM • Cobra 25 LTD... • Answered on Nov 25, 2014
0helpful
1answer

Has been peaked and tuned but wont swing but 4

what is your dk. just remember 4.5 watts is the limit
11/2/2014 10:25:54 PM • Cobra 25 LTD... • Answered on Nov 02, 2014
0helpful
1answer

I have a 4pin mic i want to hook to a cobra 138xlr mobil need to know the wiring

pin 1 audio shield pin 2 audio lead pin 3 tx control pin 4 rx control
11/2/2014 9:48:27 PM • Cobra 25 LTD... • Answered on Nov 02, 2014
Not finding what you are looking for?
Cobra 25 LTD 40-Channels Base CB Radio Logo

139 questions posted

Ask a Question

Usually answered in minutes!

Top Cobra Radio Communications Experts

Brad Brown

Level 3 Expert

18825 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

eradiostore
eradiostore

Level 3 Expert

1667 Answers

Are you a Cobra Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Cobra Radio Communications

  • Cobra Radio Communications

Most Popular Question

25ltd cb tuned peaked just replaced

  • Radio Communications
Loading...