Top 20 GPX DV7500 System Questions & Answers

tweezers...

There is a small strap that looks like a black rubber band that actionate the door mecanism. open the cab and clean it with qtip and alcohol, otherwise replace it, you'll find some at local electronics parts shop...

You can get a user manual from http://manualfox.com
Just send them a search request.

hello there. name is ryan lets see if this helps.
typically in a combination unit there is no rca audio ouputs on the tv. reason being is it is a combo unit not meant to be a item within a home theater system. it has the whole home theater built in it. ;) however if there is any audio output jacks on the tv you should be able to wire the surround sound unit up via rca cable output from tv to input on reciever for surround sound

sounds like a bad solder joint that is cracked...as GPX heats up, the crack starts to get bigger and cutting off electric circuit, then cool down closes the gap and current resumes. First try breaking and then making all possible connections outside then inside unit. Then, if no success, remove the circuit board and clean it with alcohol and brush then carefully look at each solder joint with a magnifying glass. If one found, simply re-solder it.

I've seen this problem before with devices that have audio amplification circuitry.

In the cases I've seen, the connections to the speakers were the culprits.

First of all, you should only use the GPX speakers that came with the device. I don't know what their impedance is, but if it was 8ohms, you should only use 8ohm speakers. The same for 4 ohm, 6 ohm, etc. The safe bet is to use the speakers that came with the system.

If you are using the intended GPX speakers, and they're hooked up correctly, (only one speaker per output) then I would suspect a short in at least one of the speaker wires.

Amplification circuits apply fluctuating power to the speakers which correlate the sound wave. The power reaches the speaker, has an electromagnetic effect on the speaker cone, which pushes it out or pulls it in. This produces sound. The speakers job is to be affected by the amplifier, and convert the electric power into a mechanical movement. Speakers of different impedances respond to different levels of power. Ideally, your amplifier will supply power to speakers that will use it all up and return none.

An amplifier designed to drive 8 ohm speakers will get too much kickback from little 4 ohm speakers. When I've seen this sympton before, the amplifier had another circuit designed to monitor dangerous conditions such as this and shut down to prevent permanenet damage. Another dangerous condition might be a short in one or more of the speaker wires. Inspect each and make sure none got stuck under the table, or slammed in a drawer or pinch by a staple or whatever.

--Matt

Sorry I don't have a solution. We have this model and ours is loud also, at the very lowest setting. I disconnected some of the speakers, and sometimes have to put the working speakers into a drawer to lower the sound.

sounds like you gotta power supply problem in the main unit. to repair this your gonna need a service manual most likely or you have to take it in to a repair shop to estimate for you .. if you post a schematic we will assist you in trouble shooting if you have any previous experience. Good luck.

hi the remote isnt the problem check the connections from the deck to the TV the little angle probably pulled a couple of pluges back there or something like that... very dangerous by the way he can get electrocuted!! have a good one

Hi, Open the CD and press return on the remote to reset it back to Interlace mode. Thanks Annarr

In one part of you question, you state Fox C1600 and also GPX C1600 https://www.google.com/search?q=fox+c1600 https://www.google.com/search?q=GPX+C1600 All questions need full 'make model (what it is)', first 3 words. There are too many items with those numbers. ..

I would say that as the output is 50Watts music power, a 50Watt speaker would be ideal.

Unfortunately not available anywhere. There are too many items with parts of GPX and SP-60 in them. https://www.google.com/search?q=GPX+SP-60+manual ..

there is not a needle. It is called a stylus https://www.lpgear.com/product/GPXS7794.html https://lptunes.com/collections/gpx-needles-stylus

How do I play a CD?

• Make sure the clock radio is powered on. Once a CD is inserted, playback should start automatically. It may take up to 10 to 15 seconds before CD plays.

If the CD door on your GPX CD home music system HM38170T won't open, here are a few steps you can take to troubleshoot the issue:

1. Check for obstructions: Make sure there is nothing blocking the CD door or the area around it. Sometimes small objects or debris can get stuck and prevent the door from opening. If you see any obstructions, carefully remove them.
2. Power cycle the system: Turn off the system and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on. Sometimes power cycling can help reset the system and fix any issues.

Hi 1st check there is voltage going into the transformer, if there is nothing coming out then the transformer is no goodIf there is no voltage going into transformer then check the fuse at the plug

If your GPX MW240S MP3 player is displaying an error message and not playing any music, there are a few things you can try to fix the issue:

1. Reset the player: Sometimes resetting the MP3 player can fix the error. To reset the GPX MW240S, press and hold the power button for 10 seconds, release the button, and then turn the player back on.
2. Check the music files: Ensure that the music files you are trying to play are in a compatible format with the GPX MW240S. The player supports MP3 and WMA formats, and if your files are in a different format, they will not play. You can convert the files using a free online converter.
3. Update the firmware: If the player's firmware is outdated, it may cause errors while playing music. You can update the firmware by downloading the latest version from the GPX website and following the instructions.
4. Check the storage space: If the MP3 player's memory is full, it may cause errors. Delete some files from the player to free up space.

If none of these solutions work, there may be a hardware issue with the player, and it may need to be repaired or replaced.

Instruct the computer to search for it. The computer should automatically find it and load drivers, but it should show in Windows Explorer as a volume in the left pane. Where are you looking? It will only pair with a computer if the computer has Bluetooth and most don't. Pair with a smartphone. How do I transfer my music to my device? This device is capable of playing MP3 and WMA (4ithout DRM) files. To load files requires a computer with a USB connection and the minimum requirements of Windows XP .

• Connect the player to the USB cable provided in packaging, and then connect the other end to your computers USB port.
• Once connection has been made between the device and your computer, a "GPX" drive will appear in the computer directory.
• Double click on the GPX drive
• Drag and drop your MP3 files and folders into the Music or playlist folder

https://gpx.com/on-the-go/gpx-bluetooth-mp3-player-mwb308r.html ..

RETURN IT TO PLACE PURCHASED AS DEFECTIVE .