20 Most Recent Jensen CH1001 10-Disc CD Changer Questions & Answers

Hello

I will give you a full rundown on how to install the cd changer;

Disconnect the car battery.

Run the cable from the Jensen changer to the back of your dashboard. Depending where you mount the changer, you might want to hide the cable under the carpet or run it along the door panel. Take some time before you mount the changer to figure out what is the best way to run the cable for your situation.

Remove your deck and the dashboard around it to access the back of the deck.

Locate the antenna lead plugged in to the back of your deck. Unplug it.

Find a good space to mount the FM modulator behind the dash and close enough to the deck to connect the antenna lead. You can secure the modulator to the inside of your dash by using two sided Velcro tape and place it where you need. Plug the antenna lead into the modulator's "Antenna In."

Connect the FM modulator to your deck by plugging the "Antenna Out" lead off the modulator to the antenna in on your deck.

Connect the two power cables from the modulator to your car's power. One lead goes to a constant source of power and one connects to a switched 12-volt power source.

Ground the modulator by running the black wire to an exposed screw. Wrap the wire around the screw and tighten it down so the wire doesn't come loose.

Reinstall your deck and dashboard.

Find a spot on your dash to mount the display unit. You can get creative and cut a hole in your dash and mount it that way or you can use Velcro tape and place it on your dash that way. Make sure it is close enough to the driver's seat so it can be accessed without having to reach too far. If there are loose wires hanging from under the dash you will want to tuck them under the dash and wrap them with wire ties.

Do the Screen Calibration. https://www.google.com/search?q=Jensen+9022+touch+screen+is+out+of+alignment ..

Try Jensen support for that detail. https://jensenmobile.com/support/ https://jensenmobile.com/shop/multimedia/cr271ml/

hair dryer if just moisture if water [failed seal or damaged cover ] and need to unscrew ans pry apart --but if water most likely electric circuit damage

Your Jenson model as written only appears here on Fixya in your question. The Jenson modelling numbers don't follow what you wrote so your model number 'EOA 7P' is not valid. https://www.google.com/search?q=jensen+eoa+7p ..

It sounds like there may be an issue with the mechanical components of the DVD player, specifically with the tray. Here are some troubleshooting steps you can try:

1. Check to see if the emergency eject feature is working. There should be a small hole on the front of the DVD player, and you can use a paperclip or a similarly sized object to push the button inside. This should manually eject the tray.
2. Make sure that the DVD player is receiving power. Double-check all of the connections and fuses.
3. Reset the DVD player by disconnecting the power for a few minutes, then reconnecting it and trying again.
4. If none of the above steps work, it may be necessary to take the DVD player apart and check the mechanical components for damage or wear. However, this is not recommended unless you have experience with electronics repair.

If none of these steps resolve the issue, you may need to seek the assistance of a professional electronics repair technician.

No, you cannot use a 270 watt amp kit on a 1000 watt amp. The wattage of the amp kit must be equal to or higher than the wattage of the amp it is being used for.

This video may help you https://www.youtube.com/watch?v=VC89DgWJlYw

1200 Watts at 12volts is 100 Amps. At least 16mm on a short run.

Ground the parking brake wire

My guess would be internal short

Your extension voltage has a problem

I used to own Jensen cd player for a while but I can't remember the solution of loop loading. Check Jensen cd-players manuals http://jensen.manymanuals.com/cd-players

Possibly failure of the selector

There is always a chance that you "bricked" the unit with the update. IT happens. When you get to the cross hairs you are supposed to hold your finger in the middle till it asks for the next step. IF it wont go to this, then can you retry the whole process over again. If not you have bricked it and it has to be sent in for reflash

In the back of the set you should find a small 'spade' type fuse, replace with Fuse: 15-amp, mini ATM type There is a fuse holder in on the yellow wire on the wiring harness, pull out the unit and replace fuse. User manual: http://www.jensenmobile.com/docs/common/UV10/UV10_OM.pdf Wiring diagram http://www.manualslib.com/manual/674477/Jensen-Uv10.html?page=4#manual Good luck.

I just purchased the VX7020 and went to Settings-Language-typed in 5,4,3,2,1,0 but the menu never came up. Any ideas?

This info is on the bottom of it.

Ground - negative
12v positive - switchable positive (for example, on when ignition is on, usually connected to accessory side on ignition switch)
auto ant - connected to your electric antenna or to turn on external amplifier.
Memory - connected to always on positive (to keep all your stereo presets )