Top 20 Jensen TS2050J 20" TV Questions & Answers

Your going to need to do a hard reset, look at the manufactures site on how to do this

Get a UNIVERSAL Remote for $10 and start over. It comes with the codes and is easy to set up.

No. There is no such provision. Electro help

wow that... sucks... if youve lost the remote and owners manual you could try leaving it unplugged a really long time. there are capacitors storing energy in the tv so that it remembers all the info even when you unplug it. if you leave it unplugged long enough you might be able to make it go to factory default. i hear using a screw driver to "short" the leads on the power cord can make it drain quicker. I have no idea if this will work. just don't stick the screw driver into the power outlet or try getting inside the TV... I like trying to answer your questions! I'm fairly certain after a few days of being unplugged it will forget. good luck, hope you don't need a new TV

Most RCA and GE TV sets use a four digit code to control the v-chip. The code reset procedure is different depending on the model. Try each method until you find one that works: 1. Hold down MENU on the remote and VOLUME DOWN on the TV it's self at the same time for at least 4 seconds. The set won't say so, but the lock will be unlocked 2. Hold down the 0 on the remote and the VOLUME DOWN buttons on the TV its self at the same time for at least 4 seconds. The set won't say so, but the lock will be unlocked 3. Hold down the MENU button on the front of the TV and the TV button on the remote at the same time for at least 4 seconds. 4. Hold down GO BACK on the remote and MENU on the front of the TV at the same time for at least 4 seconds. 5. Hold down EJECT on the front of the TV and the MENU button on the remote at the same time for at least 4 seconds. Depending on the model, one of the methods should unlock the V-chip. Now, if desired, you can change the settings on the V-chip by going to the MENU and going to PARENTAL CONTROLS, or on some sets, going to MENU and then going to TV SETUP, then to V-CHIP SET. If you wish to get more details, check this link. http://electronicshelponline.blogspot.com/ Pull up previous posts by its left sidebar, or type in the brand name and model number to of your set, to its search box, and press 'Enter' or view it in Mosaic / Timeslide option.

Visit this site for more details. Type in the site name "Electro-help" either Google or Yahoo search box [not in the address bar of your browser], and click search. It is an electronic equipments service help site. All details you want are there. Note the position of hyphen in between words in site name, when you type it in. The site will appear as it is in web; subtitled as service help to electronic home entertainement equipments.

Pull up older posts. You can gather all details. Sometimes, click open the adverts' by the side and bottom of each post might give you more details.

Go to the menu and set it on cable and do a channel scan or autoscan. good luck!

Look for an input button, it should toggle the source input...

hola tu el de la panasonic como estan espero ke bien solo keria saver si me puedes aser un favor por que yo tambien tengo una tv panasonic como la ke tu tienes y quisiera saver si me puedes pasar la configuracion de los colores de brillo nitides contraste y eso por que ala mi a le movierron los colores y se mira mui fea la calidad asi que si me puedes desir como van acomodados muchisimas gracias de ante mano saludosss a todos

This TV/LCD monitor has lost part or all of its controler board, you will need to open the back side of the LCD and remove the controler board, for further repair. remove and replace the controler board, to correct this problem. Also take note to check all ribon cables as well this tend to crack and also create problems with fuctionality as well.
Tank you for using Fixya.com

Hi.
No, your tv is an older model sdtv with an analog only NTSC tuner.

Newer model have an ATSC/Qam digital tuner, but not your model.

This means that if you want to watch tv, you'll have to get a converter box. It will have the ATSC/QAM tuner i it, and it converts the signal into lower definition NTSC, and then sends it to the tv through either coax cable, or rca cables.
Once in a great while you might even find one that has s-video output, but those usually are expensive.

I hope this helps you out.

Easy repair with some Super glue.Must take the tv back cover out.The FBT-the big block of plastic with a red wire with a cap hook to a CRT(tv tube).It have a high voltage gap going through a "3 inches paper clip steel bar on a FBT the big black plastic block.Put some super glue on that "3 inches paper clip steel bar on that big black plastic block.Should stop the high voltages gaps through that "3 inches paper clip steel bar causing a high pitched noises.

You can get a replacement remote here: http://www.remotes.com/remotes/servlet/rs?a=Search&o=c&uid=0&m=TS2050J&uuid=12929864096390 .

Alternatively, you can get a universal remote and try the Audiovox codes if Jensen isn't listed. You may need one of the higher end remotes to match features like changing the source of the TV. (An input/source button will be useful.) Just make sure to check if the remote code does more than turn the TV on and off and changes the channel before deciding that you have the correct code programmed.

I hope this helps.

Cindy Wells

You always need to include the model of remote and also the device you want to control.
You might find it here with the complete information:
Remotes

To remove the lock on the Jensen simpy press and hold the Display Button on the remote for at least 3 seconds whilst pointing it at the TV.

The lock will be removed and the TV will resume normal operation.

Please do leave a vote for the solution. Thanks for using FixYa.

Hello
There is an arcing takes place inside your tv. It may be from the Line Output Transformer [LOT] to neighbouring components. Please check it with the help of a technician as soon as possible, otherwise, your TV may be in great trouble in future.

Hello

Just try one amoung the following codes. I've only these three codes are available with me for Jensen Tv.

{ 0004 _0009 _0133 }

Proceedings

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

Note:- If one amoung the above four codes did't work, try the other after the TV is switched off and switch in again after some time, say at about 10 seconds, and try the other. Not enter the code continously without turning it off, after one code won't work. Ok.
__________________________________________________________________________________

If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.

1. Manually turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
5. Press and release MUTE to install the code. The indicator light goes off.

Unlock all of the channels on the TV by entering 0711 or 3308. These are the Jensen factory reset codes that will reset the TV to the original factory settings. By doing this, you will lose any information that you have stored in the TV, such as channel labels and schedules. You will have to program the TV again by going through the entire initial set up.

Good Luck,
--Matt

Check solder on the vertical output or change it. Dont know # but look for IC screew on heat sink with about 7 to 14 pins.

see on your remote control and find buttons "power", "code", "enter", "dvd" and next turn on manually your DVD. Now push both buttons at same time "dvd and code" until led light. when the led still ligth release both buttons. Try turn off your DVD using power button of your remote control as many times as be possible until your DVD coming off, after push "enter" button.