20 Most Recent Kenwood KDC-C719 10-Disc CD Changer - Page 6 Questions & Answers


disconnect all the speaker wires and power up back the unit and then press reset button at top left corner for ten second..

Kenwood Car... | Answered on Mar 05, 2019


That error is normally a shorted speaker wire but starting the car won't cause that. Possible problem could be the dimmer wire was used as a ground by mistake. Lights come on when the car starts. Another is too high of voltage. Car rests at 12 volts but is around 14 when running. Was there a plastic piece on the red or yellow wire that got cut off during the install? They have a resistor inside that keeps the voltage down.

Kenwood Car... | Answered on Mar 03, 2019


kenwood cd player pinout points-ue4hlgd00wn3h2txlnime0ky-5-0.gif
Hi, this picture resembles the harness(connecting plug) looking in from the back of the harness. The red wire goes into the A+ point. the black wire goes into the Gnd point. The yellow wire goes into the B+ point. if you not sure how to read this picture please ask the help of an installer. Cheers.

Kenwood Car... | Answered on Mar 03, 2019


YOU SHOUL CHECK YOU BATTERY AND GROUND AND REMOTE SOURCE MAKE SURE THEY ARE CONNECT PROPERLY

Kenwood Car... | Answered on Mar 02, 2019


Hi Dalitso, the sound output ic, or the ic that drives the sound to the speakers for this model is TB2931HQ. Cheers.

Kenwood Car... | Answered on Mar 02, 2019


USUALLY THERE IS NO CODE BUT IF U PURCHASE USE YOU HAVE GET CODE

OR TURN KEY AND PUSH RESET BUTTON FOR TEN SECOND THEN TURN OFF AND TRY TURN ON

Kenwood Car... | Answered on Feb 19, 2019


UNPLUNG THE UNIT WAIT TEN SECOND THE PLUG BACK IN

Kenwood Car... | Answered on Feb 19, 2019


Contact Kenwood directly and request the wiring diagram.

Kenwood Car... | Answered on Feb 13, 2019


Going in the clock menu setting and follow the steps to set clock

Kenwood Car... | Answered on Feb 12, 2019


Probably the counter wheel inside the volume button has been damaged. You can try to open it up and check the module. Mostly its a 3 pin encoder block of a standard size. Just replace it with a soldering iron.

Kenwood Car... | Answered on Jan 15, 2019


need the actual model they are all KDC

Kenwood Car... | Answered on Jan 14, 2019


I have the same amp in my car, If it is only a month old there is a internal problem with it, It should stay on when you used a jumper wire, I installed car audio for over 40 years before i retired, End was allso Am a certified electronic (Tech) PS,One thing it is not a 2 channel amp, people mistake it for a 2 channel amp because of the for speaker terminals on them, It is a mono (Bloc) Amp ,End where people go wrong on wireing them up is buy , Having each sub hooh up seperately to it, Instead of use just one of the negative end positive terminal on it , .I no the instruction for the wireing on it are confuseing, That can cause it to shot down. Allso if you have dual voice coil subs end there not wired up properly will cause it to shot down,

Kenwood Car... | Answered on Jan 11, 2019

Not finding what you are looking for?
Kenwood KDC-C719 10-Disc CD Changer Logo

Popular Tags

6 questions posted

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

The Knight
The Knight

Level 3 Expert

76390 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenwood Car Audio & Video

  • Kenwood Car Audio & Video

Most Popular Question

just got car kenwood 10disc cd

  • Car Audio & Video
Loading...