Kenwood KVT-715DVD Car DVD Player - Answered Questions & Fixed issues


According to this site, http://www.pacparts.com/library/model.cfm?mfg=Kenwood&model_id=KVT715DVD&action=list_part&back=0 , the data (brain to monitor) cable for the KVT-715DVD has the part number of 880H07-3078-72 . This is a discontinued part . There are a few EBay auctions that may still sell the part. There are no vendors that I trust that have the data cable. I wish that I had better news for you. Cindy Wells

Kenwood... • Answered on Mar 01, 2016 • 146 views


I HAVE THE BRAIN FOR THE KVT715DVD$300

Kenwood... • Answered on Apr 14, 2012 • 1,047 views


If you can, try checking your wire connections. If they check out fine, try checking your fuses and wiring for power.

Kenwood... • Answered on Apr 10, 2012 • 48 views


dude you need find the memory wire which is either a yellow or red wire that is connected directly to the battery supply if its not connected then thats your problem, look up the manual or google the wiring harness colour codes to be definate that you have the right wire

Kenwood... • Answered on Jul 21, 2011 • 77 views


try pacparts.com

Kenwood... • Answered on Mar 16, 2011 • 54 views


try pacparts.com.

Kenwood... • Answered on Feb 07, 2011 • 75 views


Hi,

Try unplugging the unit for 60 minutes, then plug back in and try it again. This will reset the processor and hopefully the unit will operate normally. Check all the speaker wiring for shorts, make sure they're also not touching the chassis of the receiver, or are not otherwise pinched or frayed. If all looks well, try disconnecting all the speakers and cycle the power off, then on again. If you have "protect" on the screen, OR the unit shuts down, or fails to power up with no load connected, then the unit has a bad output transistor, or capacitor and is in need of service. I can send you the contact info for a Service Center near you if you'd like.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Kenwood... • Answered on Nov 22, 2010 • 173 views


Hi,
Try this
The code is KCAR, First thing you have to do is have a remote-Will not work without remote.Turn on unit and the screen will come up for password.using remote press 5 two times,wait 2 seconds and press enter, press 2 three times wait 2 seconds press enter,press 2 One time wait 2 seconds then enter and finally press 7 two times and press enter! your screen will be unlocked if you did it right,If you have to try again turn off and then back on.
Thank You

Kenwood... • Answered on Nov 07, 2010 • 53 views


The data cable (IP Bus) can connect to several different component designed for your unit, i.e. xm/sirius tuner, HD radio tuner, CD changer, etc.

Kenwood... • Answered on Sep 17, 2010 • 97 views


check all your fuses. check power for the battery(yellow) wire and red wire(ignition- key must be on), and if all of those are good then check the fuse on the back of the stereo itself, i think it has a 15amp mini fuse in it.

Kenwood... • Answered on Aug 05, 2010 • 173 views


password code is kcar i have the service manual and it tells u there but i cant seem to get ot to work

Kenwood... • Answered on Aug 02, 2010 • 408 views


i have the same problem!! if you find the solution please let me know.. [email protected]

Kenwood... • Answered on Jul 24, 2010 • 383 views


hi,
although this is not wiring diagram of your gadget but still this will help you little bit. or atleast you will get some idea about wiring so by further thinking you can solve your problem...
http://www.the12volt.com/installbay/forum_posts.asp~TID~74637~PN~1 .... http://www.the12volt.com/caraudio/caraudio.asp
Hope this has helped you... Thanks...

Kenwood... • Answered on Jul 21, 2010 • 366 views


Hello did you figure out your stereo yet?
what have you tried?

Kenwood... • Answered on Jul 29, 2011 • 389 views


check handbrake wire usally green on kenwood depends on counrty, put it to ground

Kenwood... • Answered on Apr 27, 2010 • 186 views


sometimes you need to disconnect power to the radio completely for a few minutes for the microprocessor to completely reset itself. if that doesn't work, you have a problem with the cd mech itself.

Kenwood... • Answered on Mar 11, 2010 • 319 views


Hi first check the ground wire from the amp. It needs to be to a body bolt that's less then 18" from the amp and is clean no paint ect. raw metal. Also the rca wire to the amp should be ran on the opposite side of the car then the power wires. This should reduce engine noise. They also sell a noise reducer that helps in vehicles that are wired correctly but still have a engine noise.

Kenwood... • Answered on Feb 05, 2010 • 265 views


check the following link...you can get the manual for download then print it out http://www.kenwood-electronics.co.uk/products/car/multimedia/navigation/DNX5240/

Kenwood... • Answered on Jan 31, 2010 • 116 views


try pacparts.com

Kenwood... • Answered on Jan 08, 2010 • 102 views


i need the brain for that model 617 if u want we could exchange it i have the one for the 715

Kenwood... • Answered on Mar 20, 2012 • 512 views

Not finding what you are looking for?
Kenwood KVT-715DVD Car DVD Player Logo

Popular Tags

83 questions posted

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

5023 Answers

The Knight
The Knight

Level 3 Expert

76584 Answers

Cindy Wells

Level 3 Expert

6259 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...