20 Most Recent Kenwood KDC-MP4028 CD Player - Page 7 Questions & Answers

Car remotes are not like universal TV remotes, you can not program them to work with a radio they were not designed to work with.

If this is the remote that came with the radio, you may just need a new battery.

I don't have the sevice info in front of me right now to tell you if this remote is compatible with your radio.

You may be able fix this problem by clearing the E2PROM. I have seen it a few times over the last few months.

press and hold the number 3 and the number 6 key at the same time and while you are holding those in, press the reset button.

The reset button is the tiny little depressed button on the display, you will need something like a toothpick or paperclip to push it in. You can also find it in your owners manual .

If this does not work you probably have an amp problem. That means you will most likely need to replace the amp IC.

I don't know why some of these Kenwoods do this, but I just started seeing at my shop about 6 months ago.

If this fixes your problem please feel free to rate me a "FixYa"
If you need further help feel free to ask.

If you have the remote, then you can cure with the following instructions. If you DONT HAVE A REMOTE, then you will need to take it to a Kenwood agent and have them do it for you, or just buy one:) Good luck

try this

KENWOOD SECURITY CODE CLEAR procedure


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

The security is canceled and the set enters the TUNER mode!
Please rate me "FixYa" for this solution. Good Luck :)

Hi,

For wiring your Kenwood KDC-MP4028, please refer to the below wiring/color guide:
Red - Ignition/Accessory B+12VDC
Black - chassis/GND
Blue/White - external amplifier
Blue - motorized antenna
Brown - mobile phone mute sensor
White - Front Left +
White/Black - Front Left -
Gray - Front Right +
Gray/Black - Front Right -
Green - Rear Left +
Green/Black - Rear Left -
Purple - Rear Right +
Purple/Black - Rear Right -

Hope this be of help. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

KENWOOD SECURITY CODE CLEAR procedure


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

The security is canceled and the set enters the TUNER mode!

check on page ten of the manual
heres a link

http://inform3.kenwoodusa.com/manuals/KDCMP4028.pdf

try display button and volume button to get the point to enter the number. Try 1234 or 5021

This indicated that the unit is having a problem reading the disc. This can be because the disc is upside down, dirty, scratched, misaligned laser, dirty laser. Try to reset and run a cleaning disc through the unit. If it still cant read it may be a mechanical issue stopping the unit from reading the disc

Question edited for clarity. Try the ideas in the videos https://www.google.com/search?q=Kenwood+Excelon+DDX9904S+DVD+receiver+reset ..

Me radio kdc2159b is displaying the ward call,how do i remove it

To reset a Kenwood 8070 receiver without a remote, you typically need to locate the reset button on the device itself. This button is often small and recessed, so you may need a paperclip or a similar tool to press it. Consult the user manual or look for the reset button near the power or input/output ports on the receiver. Once located, press and hold the reset button for a few seconds until you see the receiver reset. Keep in mind that this process may vary slightly depending on the specific model of the Kenwood 8070 receiver.

Kenwood KDC-138 Instruction Manual [Page 18]

ManualsLib https://www.manualslib.com > ... > Instruction manual If the "E-99". code does not disappear, consult your. nearest service center. IN (Blink):. The CD player section is not operating. properly. ? Reinsert the CD.

My Kenwood KDC-d301 is giving me a E-4 error message ...

JustAnswer https://www.justanswer.com > car-electronics Aug 9, 2010 - Hello, The issue is most likely that the laser lens in the CD player itself is dirty, and not the disc. It may have been initially caused by a ... 1 answer · Top answer: You need the Kenwood radio keys that came with the unit to slide it out of the dash. It sounds ... Missing: 138 ‎' Show results with: 138

I have a KDC 138. It is stuck on OCER and will not reset.

JustAnswer https://www.justanswer.com > car-electronics > 5lw8u-... Sep 27, 2011 - This actually is DCER - you have a blown speaker. The radio is sensing a ground on the speaker circuit. Check that and let me know. If you leave ... 1 answer · Top answer: Thanks for stopping by: This actually is DCER - you have a blown speaker. The radio is sensing ... Missing: E- ‎' Show results with: E-

Cd Player Unit - Kenwood KDC-138/138CR Service ...

ManualsLib https://www.manualslib.com > ... > Service manual Kenwood KDC-138/138CR Manual Online: components description, Electric Unit, Switch Unit, Cd Player Unit. Controls Fm/Am Tuner, The Changer, Cd Mechanism, ...

This Service Manual is probably close enough for dealing with the power supply https://elektrotanya.com/kenwood_dpx-8020md_sm.pdf/download.html https://www.google.com/search?q=Kenwood+DPX-8070mj+service+manual ..

Take a look at this manual diagram. https://www.manualslib.com/manual/359815/Kenwood-Ksc-Sw10.html?page=5#manual Given the above is not your model, at least it shows the 10 pin. Ironically, below I offer a diagram of your model. The irony comes in the fact that the diagram appears labeled in Japanese But if you compare the two diagrams, maybe something will make sense from the one with the English labels. Otherwise, you might fire off a query to Kenwood customer support. https://www.manualscenter.com/manuals/kenwood/kscsw900-owner-manual.html Here is a 10 pin harness compatible with the subwoofer. Kenwood Subwoofer Amp KSC Wa100 Wa80 Sw10 10 Pin Harness for sale online ' eBay I don't have any information on how to power supply a kCSWA900 Kenwood subwoofer. However, I can tell you that the Kenwood KSC-SW10 compact powered subwoofer has a built-in amplifier with a 38 watts RMS power and a wired remote for control over volume level, variable low-pass crossover (50-120 Hz), and selectable phase control (0°, 180°) . The subwoofer comes with a power/ground wiring harness and preamp (RCA) and speaker-level inputs .

In the link plus a video, albeit on a different model. https://www.google.com/search?q=kenwood+94+amplifier+p-off+switch

The Kenwood KAC-7252 and KAC-9104D are both great amps, but they have different strengths and weaknesses. The KAC-7252 is a 5-channel amp that can output 75 watts per channel at 4 ohms. It also has a built-in crossover and time alignment, which can be helpful for getting the most out of your woofers. The KAC-9104D is a 4-channel amp that can output 100 watts per channel at 4 ohms. It also has a built-in subwoofer output, which can be used to power a separate subwoofer. If you are looking for an amp that can power all of your speakers, the KAC-7252 is a great option. It is also a good choice if you want an amp with built-in crossover and time alignment. However, if you are looking for an amp that can power a subwoofer, the KAC-9104D is a better choice. It is also a good choice if you want an amp with more power output. Ultimately, the best amp for you will depend on your specific needs and budget. If you are not sure which amp is right for you, it is always a good idea to consult with a professional car audio installer. Here is a more detailed comparison of the two amps: Kenwood KAC-7252

• 5-channel amp
• 75 watts per channel at 4 ohms
• Built-in crossover and time alignment
• MSRP: $399

Kenwood KAC-9104D

• 4-channel amp
• 100 watts per channel at 4 ohms
• Built-in subwoofer output
• MSRP: $499

I hope this helps!

whatever makes it mute from whatever it is you are in

$4.95. No free ones https://www.google.com/search?q=kenwood+dpx-6200m+manual ..

This often doesn't work because the radio is monitored by the Body Control Module on the 5 volt computer network. Wiring

Subaru Legacy, Outback, Baja (1993-2008) Car Stereo ...

Pinout Guide https://pinoutguide.com > ... > Subaru pinouts Oct 22, 2019 - Pin #. Function. Legacy / Outback / Baja Factory Radio Connector Wire Color (wires go to car's Speakers, etc.) Subaru After-market Harness ...

2000 Subaru Impreza Car Stereo Wire Colors and Locations

the12volt.com https://www.the12volt.com > installbay > stereodetail 2000 Subaru Impreza Stereo Wiring ; Left Front (-), Green/Black ; Right Front (+), Red/Yellow ; Right Front (-), White/Black ; Rear Speakers, 6 1/2" Rear Doors. Installation kits https://www.google.com/search?q=2000+subaru+outback+stereo+installation+kit ./.