20 Most Recent Kenwood VR-407 Receiver Questions & Answers

How do I fix the inputs on my Kenwood vr-407? the radio places sound but I don't get any sound from any of the other inputs cd/dvd aux / tape, video, monitor nothing but radio plays sounds

Kenwood VR-407... | Posted on Nov 21, 2015 | Be the first to answer

Have a VR-407 receiver, all of a sudden there's no

Check for basic things like speakers being turned off or switched to speaker b from a and the tape monitor switch being on. Larry's Electronics.

Kenwood VR-407... | Answered on Aug 11, 2014

0 Answers

Have a kenwood vr 407 and is was aying e and all of a sudden it mae a click and now no sound out of any speaer at all...the power and display are still on but it does any sound at all thru any input m

Kenwood VR-407... | Posted on Aug 11, 2014 | Be the first to answer

0 Answers

Hello everyone, I have a Kenwood 5300 receiver and when I turn it on mute light flashes three or four times and then it goes into standby mode. Anyone know this problem?

It's going in protection mode. Maybe relay issue. Need to bring to a tech to correct the issue.

Kenwood VR-407... | Answered on Apr 05, 2014

1 Answer

Kenwood VR-407 always stays in Stereo mode

You will need to go to audio set up and make sure it is set up to play with a center chanel if you have one as well as the surrounds. You can also only have side a speakers selected when trying to use surround. If you have b selected it will play in stereo only

Kenwood VR-407... | Answered on Feb 11, 2014

2 Answers

Kenwood basic M2 Amp Lightning strike

you can check the output transistors for short circuits with the low ohms range or diode checker . If they have failed, then it is often a good idea to replace all as much stress can be placed on an output array in this type of failure. to repair reliable, all outputs on an offending channel should be replaced.

Make sure the fuse you replaced was the same type of fuse. check markings.... T stands for sloblo... a fast blo duse may let go at turn on. The power supply may have a shorted rectifier diode in it also.

be aware however, every time a fuse of that rating blows... more damage may be occurring to the amp.

Kenwood VR-407... | Answered on Jan 30, 2014

0 Answers

No sound out of reciever

Kenwood VR-407... | Posted on Dec 24, 2013 | Be the first to answer

0 Answers

Kenwood subwoofer buzzes loudly

Kenwood VR-407... | Posted on Dec 03, 2013 | Be the first to answer

0 Answers

Vr kenwood

Kenwood VR-407... | Posted on Oct 23, 2013 | Be the first to answer

0 Answers

Turning off and red light is flashing

Kenwood VR-407... | Posted on Sep 20, 2013 | Be the first to answer

0 Answers

Vr407 no sound from cd input but works from tv &

Kenwood VR-407... | Posted on Sep 15, 2013 | Be the first to answer

2 Answers

Cant get the wiring figured out.........

TV is HD correct? Use the Y/CB/CR from the Sat to the TV. Use the Digital optical cable for sound from the sat to the receiver. Use the s-video from the dvd player to the tv and the l/r to the receiver for sound. I would suggest upgrading to another set of Y/CB/CR cables to connect your dvd to the TV and benefit from better picture. Also, buy another optical cable for dvd sound (so you can enjoy surround sound). Your receiver has two optical inputs so youre covered there.

Kenwood VR-407... | Answered on Jul 10, 2013

1 Answer

Manual

Connection instructions begin on page 8 of this manual: http://inform3.kenwoodusa.com/manuals/VR407.pdf

Kenwood VR-407... | Answered on Jun 12, 2013

1 Answer

Manual

Connection instructions begin on page 8 of the manual at http://inform3.kenwoodusa.com/manuals/VR407.pdf

Kenwood VR-407... | Answered on Jun 12, 2013

1 Answer

I have no sound coming out of my sub woofer on my kenwood VR-407 everything else works great anyone have any ideas or solutions

yes it very much has everything to with it. your sub out is at a pre-amp lvl, so you can route that signal to another amp, then to your passive sub, or get a powered sub

Kenwood VR-407... | Answered on Apr 20, 2013

0 Answers