Top 20
Kenwood CT 401 Hi-Fi Stereo Dual Cassette Deck Single Dual Cassette Deck - Page 7 Questions & Answers
Can I connect Harman kardon 7.1 amp with my kenwood EQ7030 if so how?
It would be normal practice to connect the Equaliser via the tape in and out of the amp, to the Equaliser in and out. If you are using a tape deck, then that goes into the Equaliser's sockets for tape decks.
I wouldn't use the Equaliser on any of the Dolby or other coded sound modes as it could effect the signal.
Have a Kenwood vr 606. The sub keeps shutting off. You can hear a relay click when it happens. A jiggle of the cord at the sub output will restore sound to it. I believe its a bad connection between the port and the board but not sure. How and where can I get this fixed
Hello Jason, from what you are saying, it would seem that the problem is inside the Subwoofer speaker, I do not think it originates in the Kenwood
Before you try changing the RCA-RCA cable between the Kenwood SubWoofer output and the Subwoofer speaker input
Also control the power cable of the subwoofer, if it is with an interlook, replace it
You have not commented that Sub you have, tell me the brand and model
If with these tests, you do not have positive results, take the Sub, to a specialized technical service
I hope you can solve this issue
Greetings Franco Dosil
Hola Jason, por lo que comentas, parecer?a que el problema esta dentro del bafle Subwoofer, no creo que se origine en el Kenwood
Antes prueba cambiar el cable RCA-RCA entre la salida de SubWoofer del Kenwood y la entrada del bafle Subwoofer
Tambi?n controla el cable de alimentaci?n del subwoofer, si es con un interlook, reemplazalo
No has comentado que Sub tienes, dime la marca y modelo
Si con esas pruebas, no tienes resultados positivos, lleva el Sub, a un servicio t?cnico especializado
Espero que logres resolver este tema
Saludos Franco Dosil
How do I connect my Kenwood 107VR Receiver to my TV for surround sound using the speakers attached to the receiver?
Hello Laura, your Kenwoon, does not have digital audio inputs,
Neither Fiber optic input, nor Coax, nor HDMI
only stereos, if you can connect your television, if you have analog output and enter it in your Kenwood
I am sending you the user manual of the 107VR Receiver, to observe the possibilities that you have
I hope you can enjoy your equipment
Greetings Franco Dosil
Hola Laura, tu Kenwoon, no cuenta con entradas de audio digital,
Ni entrada de Fibra optica, ni Coaxil, ni tampoco HDMI
solamente entradas estereos, si puedes conectar tu televisor, si tiene salida de analogica e ingresarla en tu Kenwood
Te estoy enviando el manual de usuario del 107VR Receiver, para observes las posibilidades que tienes
Espero puedas disfrutar tus equipos
Saludos Franco Dosil
https://www.manualslib.com/manual/777099/Kenwood-107vr.html
Help!!!
I have a temperamental kenwood kmix machine. ??. I have to talk to it nicely and ask it to work otherwise it doesn’t switch on!! Any advice on why this might be happening is greatly received. My family think I’m bonkers talking to a machine ??
Hello Zoe, I do not know about this type of devices, do not pay attention to your family, keep talking to the machine, in short, you work with it and it's good to get along
Good luck, I hope you understand and that you can solve the issue
Greetings Franco Dosil
Hola Zoe, no conozco sobre este tipo de aparatos, no le haga caso a su familia, siga hablandole a la maquina, en definitiva, usted trabaja con ella y es bueno que se lleven bien
Suerte, espero que se entiendan y que logre resolver el tema
Saludos Franco Dosil
How to connect a Kenwood audio video surround system to a Kenwood km 209 amplifier
Hello Patricia, the Kenwood KM 209, is a two-channel stereo amplifier, you can only send two signals and amplify them, for example, Left and right front or Main audio output and you will have greater presence of frontal sounds
Audio output left and right rear or Surround, you will have greater presence of the rear sounds
It has the ability to amplify only two channels only
I hope you have clarified the possibilities
I send you the user manual, so you can observe the connection possibilities
Greetings Franco Dosil
Hola Patricia, el Kenwood KM 209, es un amplificador estereo de dos canales, solo puedes mandarle dos se?ales y amplificarlas, ejemplo, Salida de audio izquierdo y derecho frontales o Main y tendras mayor presencia de los sonidos frontales
Salida de audio izquierdo y derecho traseros o Surround, tendras mayor presencia de los sonidos traseros
Tiene la capacidad de amplificar solamente dos canales solamente
Espero te haya aclarado las posibilidades
Te envio el manual de usuario, para que observes las posibilidades de conexion
Saludos Franco Dosil
https://www.manualslib.com/products/Kenwood-Km-209-3868175.html
Kenwood micro hifi model rxd-m33v ariel output
The FM aerial input is simply just a female banana socket.For FM reception, you can use any thin insulated wire, keeping it clear as possible from TV screens, fluorescent tubes, to minimize interference. For the plug, strip end of wire 2 in (50.8 mm) long, fold bared part back on itself to form a U-loop about 1 inch 25.4 mm long, squeeze it a bit so end is V-shaped, insert into socket.Long wire boosts signal strength.A matchstick can help to secure the wire in socket.EDIT:Best to try get hold of the proper FM single-wire antenna which has 75 ohms matched impedance and correct plug for best signal.If AM reception is required, you need an AM loop antenna.For more details, visitmanualslib.com
Kenwood KR-A5010 home stereo takes several minutes to ''warm up''
It's probably a voltage regulator that feeds the main power amp. It will need to be replaced if it is. The way to find out would be to spray the faulty device with Servisol Freezer spray while the system is up and running. If it then goes dead it would confirm it's faulty.
Not finding what you are looking for?