20 Most Recent
NAD L40 CD Player - Page 6 Questions & Answers
NAD 3130 one channel stopped working, tip what to do first?
May not be serious,first with good channel playing move all controls and switches on the amp,Dead spots can occur on controls especially if they are rarely used.balance controls,tape monitor switches etc so work them all.If fault doesn't clear try headphones,switched sockets can cause problems.next swap input signal leads,left to right. and if still no good try swapping over speakers left to right.STILL no sound? its the amp.Time for tools and a test meter.You can look for blown fuses but its never a good idea to replace a blown fuse without testing the circuit first.may cause further damage and put up the repair cost
1/13/2015 9:34:31 PM •
NAD Audio...
•
Answered
on Jan 13, 2015
My NAD T747 keeps shutting down in Protection Mode at 6db when it used to go much louder. I cleaned the unit. Still nothing.
Modern AV receivers such as your NAD have protection circuits to prevent damage when there is a short on the speaker terminals. Look carefully at the speaker connections on the back of the AV receiver- for example, the speaker cable for front left speakers labelled + and - : there should not be any stray strands of wire that connect from + to - ; this would be a short circuit. Check each of the connections on the AV receiver as well as on the back of each of your Speakers themselves. Also ensure all connections are snug (do not use pliers). If this does not solve your problem, you may need to take your AV receiver on for a service checkup. Good luck !
12/13/2014 12:04:16 AM •
NAD Audio...
•
Answered
on Dec 13, 2014
C70 heater fan
What is the question? More information is needed before somebody can help you. What is a C70
11/4/2014 8:40:14 PM •
NAD Audio...
•
Answered
on Nov 04, 2014
I have an HTR-2 NAD remote. All the buttons except for the ON button are working. is there anyway to fix this?
Remote controls have an operating code which entered right will cause all functions to work. However if you were given the wrong remote or it doesn't have the right code, certain buttons will not work.
Check that the appliance it operates is the right model for the remote. Some remotes will allow reprograming others are fixed. If you can reprogram it will be just a question of finding out which code the amp uses and entering that. You can search online for the codes for your model.
It's not uncommon for the wrong remote to be sent out when first sold. Some people don't know it's wrong as the remote works nearly all the functions, just not all.
8/22/2014 11:47:46 PM •
NAD Audio...
•
Answered
on Aug 22, 2014
How to connect ONYZ home kit sirius to a NAD T775?
Try a factory reset of the receiver.
To perform a factory reset, press and hold the MENU and SOURCE buttons until Factory Reset is displayed. Then Power Off from Back panel for 1 minute and power up normally.
You may have damaged the receiver if you did not power off before installing the Onyx module.
7/28/2014 3:14:24 PM •
NAD Audio...
•
Answered
on Jul 28, 2014
Inputs not working
What model NAD?
Does the power light come on?
Is there a light "Click" sound from the amp after power ON ?
5/27/2014 11:54:17 AM •
NAD Audio...
•
Answered
on May 27, 2014
No sound
If you have cables running to speakers, ensure that the cable's have not been disslodged, broken (need a circute tester). If the speakers are within the unit, I suggest you get a technician to check it out or serious damage can be caused.
Last suggestion is if you have the manual or can get one, read the setup instructions. Good luck.
4/16/2014 10:12:41 AM •
NAD Audio...
•
Answered
on Apr 16, 2014
Not finding what you are looking for?