20 Most Recent Panasonic CT-32D12D 32" TV Questions & Answers

cable signal is weak. Tech. must check house wiring.

Panasonic... | Answered on Dec 03, 2016

Unplug it and take the back off. Look too see if the fuse right next to the power cord is black. Replace it. If it pops again, you have damaged the board and need a repair guy. Look for any burnt parts before replacing the fuse.

Panasonic... | Answered on Jun 16, 2011

Resolder the vert output IC, if this isnýt the solution you must replace the IC.

Panasonic... | Answered on Aug 15, 2010

What do you mean "the color is going on it " Do you have no color sometimes/poor color/tint or skin tone not correct/image is dull?

Panasonic... | Answered on Oct 20, 2009

bad connections inside , solder have to be done inside

Panasonic... | Answered on Sep 13, 2009

Loose connections on power supply and vertical IC.Resolder

Panasonic... | Answered on Aug 05, 2009

The first thing you can do is try plugging it somewhere else. Sometimes its the wall outlet. Unplug it and check to see if the plugs don't wiggle. Sometimes the metal plate on the plugs has broken loose. While it is plugged in move the cord to see if it does it. When all that don't determine the problem. You can open the TV, and check for loose connection, and cracked solder joints. Look aroun the flyback area because thats where most cracks develop because of its weight. I really don't recommend opening the TV because you could make the problem worse if you are not carefull. Also the tube can have lethal charge even if not plugged in, and some TV this charged remain for up to three days. Good luck.

Panasonic... | Answered on Jun 29, 2009

There is one way to test a remote control. Turn on your pc cam. Face the remote control to it, and as you press any of the buttons you should see blinking lights from the Infrared emmitter diode. Our eyes can't see this but a pc cam can. You can also use a camcorder or a camera phone. If you see light blinking the remote is bad. Just get another remote, maybe a universal one. If the remote blink most likely the problem is the device in which you are using the remote to control whatever it is. In the front there is an infrared recieving module. Try replacing that, you would have to open the device of course, and make sure you don't touch ruin anything in there with static electricity. You would need a soldering iron, a desoldering wick, and some solder to replace it. Other than that it is a job for electronic technician.

Panasonic... | Answered on Jun 27, 2009

check and or replace the following :
repair must be done by qualified tv pesonnal

Panasonic... | Answered on Jan 23, 2009

Click here to download the user's guide and go to page # 9 of the pdf file, the instructions on how to connect the audio to the surround sound or amplifier are there.

Panasonic... | Answered on Sep 06, 2008

hi dear
sound like to me it's screen voltage too hi check some cap on CRT base value 1mf 200v or above.at the same time u can check the cap on horrizantel 2.2mf 250/300/450vot some wear .have good luk

Panasonic... | Answered on Dec 19, 2007

Not an easy fix because of the smoke which means that there is a short from a bad ground that may have blown a capacitor because of a loose connection. Often a short on the circuit board results in having to get a new one because of damage from the sparks. Make sure it is unplugged at all times until someone can open it and look. With any luck, the damage is light and the loose wire can be re soldered at minimal cost.   

Panasonic... | Answered on Oct 30, 2007

solder all around the flyback area if this not resolve the problem replace the flyback

Panasonic... | Answered on Dec 13, 2006

power supply, or luminance driver boards need replacing $300? for the latter.

Panasonic... | Answered on Dec 09, 2006

Your problem is in the vertical deflection circuit. If you know how to solder it may just be a cold solder connection, but if you try to solder it and it still does not work, you may have a bad Vertical output IC. This set has really no user replaceable parts unless you have some no how on serviceing solid state printed circuit boards. If you dont , my advise would to seek out a repair depot and have them fix this set for you. It should not run more then 150 bucks or so. Good Luck Ps please do not forget to rate this thread.

Panasonic... | Answered on Nov 12, 2006

i would not recomend replacing the 7w with the 5w, beacuse the resistor will allways run hot, hotter then the resistor should be. the resistor could possible melt anything that touches it & will not last as long as the original before it goes bad. find a 7w, if just for safty reasons.

Panasonic... | Answered on Nov 06, 2006

I have already responded to your first question in relation to the Ohms and wattage,It worries me that maybe you can not see an answer to that question.The wattage rating should be the same or highier.

Panasonic... | Answered on Nov 01, 2006

Check this out. http://www.pasc.panasonic.com/Epartr/PartsList.asp

Panasonic... | Answered on Oct 31, 2006

Not finding what you are looking for?
Panasonic CT-32D12D 32" TV Logo

29 questions posted

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts


Level 3 Expert

5700 Answers

The Knight
The Knight

Level 3 Expert

76416 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Panasonic Televison & Video

  • Panasonic Televison & Video

Most Popular Question

power flickered during thunderstorm tv

  • Televison & Video