20 Most Recent
Panasonic DVD-RV32 DVD Player - Page 4 Questions & Answers
Panasonic dvd-rv32 region unlock?
HELLO
I am concerned about this problem as I don't know which country you are trying to use this unit in! If this DVD player is Canadian I would make sure of your countries mains voltage BEFORE plugging it in! If the mains voltage is MORE than 110/120 volts @ 60hz then you are going to have a problem unless you have a unit to drop the voltage to the required level. If you attempt to pump 230 volts through it damage WILL occur!
Now for your solution. To hack the player with your units remote will not get you very far, however if you go to www.genuinecopies.tv on the web they can supply a remote that will hack the unit and make it region-free and they DO work.
Forgive the long answer, but I just want you to use the unit safely!
ALL THE BEST (:-)
10/21/2009 1:14:14 PM •
Panasonic...
•
Answered
on Oct 21, 2009
Code h07 comes up
This is the major deffect design in the spindle motor.
Take the cover out put some WD40 in the spindle motor,leave it soak for about 20-30 mins.should work,after the motor it oil up.
10/19/2009 4:37:40 PM •
Panasonic...
•
Answered
on Oct 19, 2009
Error code h07
HELLO
I have just recently posted a cure for this - but here we go again. Fault H07 is the fault code for the spindle/disc motor and to cure it do this!
With the lid of the player removed, locate the spindle and where the motor shaft goes into the motor itself, use a little light oil or WD40. Let it soak in a while and try it again - you should now find it works.
Why this works I just don't know - it just does! (:-)
9/9/2009 7:54:50 AM •
Panasonic...
•
Answered
on Sep 09, 2009
It appears that it is saying that it is hot.
if your player is overheating, it is pretty much dead. try contacting Panasonic to at least report this, in-case they may know there is an issue.
overheating can be caused by an electrical-short and may eventually cause fire -failures which usually require a safety-recall and you will get a replacement.
if your player is on top of a Television, remove it and see if it still has the problem.
9/3/2009 2:33:33 PM •
Panasonic...
•
Answered
on Sep 03, 2009
Hello, i want to know how could i chang the
this is probably not possible :(
if you have lost your remote, you can get most any universal remote control and it will include simple directions to program it to work with your player.
8/30/2009 8:58:56 PM •
Panasonic...
•
Answered
on Aug 30, 2009
H01 Error
H01 means that there is an alignment problem or there's a faulty lens mechanism. Align it would cost about $50 . If there is a faulty part , then cost would start from about $80 labour plus part.
8/8/2009 4:59:57 PM •
Panasonic...
•
Answered
on Aug 08, 2009
How do I connect my dvd to my tv???
connect component{red, green, blue} cables to corresponding color on back of tv or yellow, red, white cable to back or front of tv and select input on remote. May be component labeled or video 1, 2 and etc...Make sure dvd player is turned on first.
8/4/2009 3:54:45 AM •
Panasonic...
•
Answered
on Aug 04, 2009
My t.v has a digital decoder and I can't get my
use the red/white/yellow jacks from the digital box to the VCR input, then set the VCR to L1 or line 1, you will not be able to use the timer function on the vcr but it works for playback, due to the change over from analog to digital your timer is now useless
7/17/2009 3:45:55 AM •
Panasonic...
•
Answered
on Jul 17, 2009
My unit says locked and the disc compartment won't
Your best bet is to completely power down the unit, unplug it from the wall, allow it to sit for a good 3 - 5 minutes, and plug it back in. Then try to eject the disc at that point. If it still shows locked and won't eject let me know by replying to this and I will look to see if there is a manual eject procedure, not familiar with one off the top of my head. Chances are very very good that powering down completely, unplugging, and re-powering will work.
7/8/2009 12:26:11 AM •
Panasonic...
•
Answered
on Jul 08, 2009
H07 code appears on the read out
hi..the reason to this problem is the motor.It may
be either spindle motor problem or the motor is not
spinning up.
check this out..
thank u..
kindly rate my response..
6/9/2009 5:30:17 PM •
Panasonic...
•
Answered
on Jun 09, 2009
Panasoic dvd rv32
See if your dvd don´t get the progresive scan sistem activated if they got it deactivate
5/9/2009 2:33:50 PM •
Panasonic...
•
Answered
on May 09, 2009
Dvd
I opened it up and sprayed silicone on the center where the disc snaps on. I also sprayed from a side angle to try to aim it towards bearings/works underneath. It worked!
4/25/2009 6:31:52 AM •
Panasonic...
•
Answered
on Apr 25, 2009
Not reading dvds or cds
press and hold REWIND and PAUSE on the unit and then also press and hold OPEN/CLOSE until innitiliazing appears try several times
4/12/2009 11:09:42 PM •
Panasonic...
•
Answered
on Apr 12, 2009
Not finding what you are looking for?