20 Most Recent Panasonic PT-51HX41 51" Rear Projection Television Questions & Answers

Panasonic 41" color quality

t-con controller board on the back of the screen, screen is split into 2 the t-con board blends them together and displays the signal into led format. this board can be replaced, just make sure the board id the same number and same version number as old one. magnets only worked on crt screen. and not very well.

Read full answer

Panasonic... • Answered on Feb 02, 2018

1 Answer

Panasonic PT-51HX41B, Not a problem but some info for Ladywinn

Be the first to answer

Panasonic... • Posted on Mar 06, 2017

0 Answers

Replace IC Convergance chip in Panasonic PT-56HX41PF

Enter the tip of a pointed knife between the left side edges of the connector (circled in black in the attached pic) and gently tilt the knife away from the connector. Do the same on the right side. The connector should pop up.

Read full answer

Panasonic... • Answered on Jul 18, 2014

1 Answer

How do I reset factory settings for a panasonic projection tv?

Be the first to answer

Panasonic... • Posted on May 28, 2014

0 Answers

Rest the tv, where is the reset button?

Be the first to answer

Panasonic... • Posted on Apr 22, 2014

0 Answers

Picture not clear. letters blurred

Be the first to answer

Panasonic... • Posted on Jan 06, 2014

0 Answers

Panasonic tv pt43lc14 steady flashing red light tv does not turn on

Be the first to answer

Panasonic... • Posted on Jan 06, 2014

0 Answers

My Panasonic Projection TV PT-51HX41 shuts off after a few seconds & won't turn back on.

Be the first to answer

Panasonic... • Posted on Nov 25, 2013

0 Answers

pdf Manual

PT-51HX41 51" Rear Projection Television Manual

Panasonic Televison & Video | Uploaded on Oct 13, 2013

I have a PAnasonic Plasma that is shuting off

Be the first to answer

Panasonic... • Posted on Sep 03, 2013

0 Answers

A3809AM ES REMPLASO EL CXA3809M

Be the first to answer

Panasonic... • Posted on Aug 13, 2013

0 Answers

Tv has dark screen

Be the first to answer

Panasonic... • Posted on Apr 14, 2013

0 Answers

TV Won'T Turn On

A fuse is not your problem. this TV has a safty feture that when it senses a problem it cuts the power to prevent any fouther damage, when you un plug it the TV resets and it will turn on agian. I have the same TV Check the CRT light guns there are 3 of them. If one goes bad it will cause your problem.

Read full answer

Panasonic... • Answered on Mar 21, 2013

2 Answers

Picture is tilted and bottom of picture is cut off

Might be convergence problem if looks like at all the attached pictures---I have instructions for this repair and parts cost is not high--about 30 dollars.let me know if this is the issue and what your skill level is as soldering is involved here.

Read full answer

Panasonic... • Answered on Nov 03, 2012

1 Answer

Projection tv lamps

All fillament based lights will dim as they age. Some of the newer/better types it will be unnoticible. If you are losing image quality or brightness you may have a bulb that is nearing the end of it's life cycle. A glance at you owners manual or the manufactor's website should give you an indication of the expected life of your bulb. Also most of the projector made in the past few years have a counter that tallies the amount of hours your bulb has been on. A more likely culprit is probably dust accumilation somewhere inside your projector. Most projectors have filters these days and need to cleaned at certain intervals and in certains ways. Not cleaning these filters can cause heat build up that can increase operating temps and shorten the life of your bulb and or projector. Or sometimes jsut fail and cause a dramatic decrease in image quality. Again these things are vendor/model specific so you will want to check with them about your particular model. Hope this helps.

Read full answer

Panasonic... • Answered on Sep 18, 2012

1 Answer

Panasonic PT-51HX41 51 inch

the blinking power indicator is actually a error code. How many times does it blink as I can assist you if you let me know how many times the led blinks

Read full answer

Panasonic... • Answered on Sep 18, 2012

1 Answer

Sound but no picture!

I would double check the wire connections especially the bridged connectors that connect the A and D boards also see if the wire from the front panel PCB is actually hooked up. Often its easy to get a wire plug mixed up and plugged into the wrong socket or not seated properly.

Read full answer

Panasonic... • Answered on Sep 18, 2012

1 Answer

My Panasonic cinema vision tv

Problem is called convergence; see attached photos.

This set uses 2 of the STK-392-110 convergence chips, both will have to be replaced and total parts cost on EBAY will be under 25 dollars.

The good news is I have start to finish step by step instructions for this repair in this set. They tell you everything you will need and exactly how to do it.

They are based on my experience doing this repair in hundreds of sets just like yours.

I will enclose also a photo of what the chips look like.

If you want the instructions let me know and we will find a way to get them to you for free.

If this information told you something you did not know, rate this solution as I do this here for free.

SD TECH

This is a JVC board but it uses the exact same chips (black) that are in your set.

Read full answer

Panasonic... • Answered on Sep 18, 2012

1 Answer

Can't see picture but have sound on Panasonic pt53tw53g

Be the first to answer

Panasonic... • Posted on Sep 16, 2012

0 Answers

Bad color then no power on 51'' panasonic cinemavision

Check the power light for blink code--usually if this model shuts down the power light will blink in a sequence--3 blinks a pause and 3 blinks is short protection--usually means a convergence circuit problem.

Let me know what you find--I am here to help.

if this helped you rate this solution as I do this here for free.

SD TECH

Read full answer

Panasonic... • Answered on Sep 10, 2012

2 Answers