20 Most Recent Toshiba WRC-1000 Router (PA3227C1ETC) Questions & Answers

Try cable connection, the X-Box will run better on online games anyway with cable connection. WEP mode was obsolete years ago and represents a real security hazard. Changing the router for a router with AES2 will enhance your security. Cable will make security better too.

Well, all of the routersseem sto work failry much the same, and certainly the function is the same...just how you interface is different. Below, I am providing a list of the things that I prefer to change.
The key with routers is they are meant to be adjusted by Geeks, ONE main detail is you have to save before you leave a page, or your changes are discarded, without notification that you would expect.

SAVE every change and you should be okay.

So, go to the website for your router maker, and get the manual. Typically, you connect to the router and put in the address bar a direct address like 192.168.1.1. or very similar.

Then you can change what you need to or better yet, comb through and set as suggested below:

Wireless Router

It is usually easiest to run the install wizard, but be sure to be ready to set the items listed below.

Things to set:

Note: Routers are intended to be set by geeks. You have to SAVE EVERY page, or the changes will be lost. A geek knows this (apparently). The router gives no protest...just dumps your changes.

1. Login password (RECORD THIS!!). Consider taping to bottom of the router. Physical access is not the security issue.

2. Set a recognizable system ID.

3. Invoke wireless security of at least WEP.

a. Assign your own access code, 10 digit home or cell #. Consider taping to bottom of the router. Physical access is not the security issue.

4. Check that your router is set to broadcast its' presence.

You can reset the factory defaults, then login using the original username and password.

To reset the Wireless Routing Center to factory defaults, insert a straightened paper clip into the Load Default hole on the back of the router to press the button. Keep pressing and turn the Wireless Routing Center off and on. Wait for at least five seconds before you release the button. Then wait for the Wireless Routing Center to finish booting.

By default, the user name is admin and the password is password.

192.168.10.1

Hello there!

If you forgot your password on your router, you can always put on fabric settings, just hold little button behind your router for 5 to 10 secconds, then restart router, and you will put it back on fabric settings.

Please rate my solutions! =)

Sincerely
Aleksandar Adzic

... and your problem is _________________________ ???

With an Ethernet cable, connect the "wired" port on your desktop/laptop to one of the "wired" ports on the router.

Access the router's built-in web-server, and "reset" the router to "factory-settings".

Then, run the "Wired Networking Setup Wizard".
Then, run the "Wireless Networking Setup Wizard",
to configure your wireless network, for up to 250 wireless devices (iPod Touch, laptops, et cetera).

FIXYA does not allow "out-of-band" communications between questioners and experts.

You want to secure the wireless network.
Is there any computer connected to the router with the Ethernet cable?
If not then you will need to connect the computer to the router with the cable.
Check the IP address on the computer. Open the router set up page.
Once you open the set up page, you will find the option to make it secured

Click Here for step by step instructions

Hello
Access your router with http://192.168.10.1
type user as "admin" and password as "admin" and password as "password"
Then click on WEP security make sure WEP 128 bit is enabled.
Also enable SHARED
Then add your wep key in first text box then click on system and save and reboot router.
Let me know if you need further assistance.

Are you trying to connect to the wireless network on the laptop ?
or you are trying to connect to the internet with the cable.
What is the operating system on your laptop ?
It is very simple to connect to the wireless network?
Click Here for more info

I am not familiar with your particular make and model. Normally, you can configure such a router with no password. Many people will say you need a password for security and I will not disagree. However, I think a password is at your option. If there is a password on your device now and you forgot it, I'd try :"Admin". You may wish to check the documentation that came with your device or check with the manufacturer.

Let me know if this works for you.

A

So your first problem is to learn how to login to your router. Please see your documentation. You can usually find the documentation for any router/homegateway at the vendors website.

If you still can't logon you may have to do a "hard reset" of the router/gateway to force it back to the default logon/password.

Now having solved that you need to understand that the largest MTU setting that you can use to increase your internet performance must be equal to or smaller than the smallest MTU setting between you and your internet target. If you make the MTU larger than that it will slow down your connection because it will now have to use 2 frames transmit and recieve what it used to only use one for.

While there are tools that can help you with that, the simplest solution is to find out what your ISP says the MTU should be.

Tom

hook computer up to router with the eithernet cable first, then in internet address bar, type 192.168.1.1
Then this will bring you to your router configuration page.
If it does ask you for username and password and you have not set it up yet, then try using
Username: admin
Pass: admin

try to unplug it and wait 10 to 15 sec restart your computer and plug the router back in should work fine If you need further help, reach me via phone at https://www.6ya.com/expert/david_eb7ea98642566cc6

The WEP key is in the software that setup your wireless network for the router or modem whatever you are using. Whoever set it up knows what the WEP key is. If you have any questions let me know.

Try entering "admin" for the user and "password" for the password.

Check this link http://portforward.com/english/routers/port_forwarding/Toshiba/WRC-1000/Xbox_Live_360.htm
hope that helps...........

hi,
          have you  open the ports of  your router  ?