20 Most Recent Sony KP-53S65 53" Rear Projection Television - Page 5 Questions & Answers


how many times does it blink?

Sony KP-53S65... | Answered on Jun 10, 2008


much to my suprise these tubes need to be re-juvenated with a crt shooter. this does not bode well with the so called king o the hill (sony). although after re-juvenating the tubes seem to hold up rather well.

Sony KP-53S65... | Answered on May 24, 2008


Hi, The blinking lights is an indicator of an internal fault. On some Sony sets, 4 blinks indicate a problem where the video is muted due to a component fault. Since this involve opening the set and doing electronics diagnosis and possibly component/board replacement, you may be better off seeking the services of a qualified TV repair professional. Hope this be of assistance/idea. Post back should you need further information. Good luck and kind regards.

Sony KP-53S65... | Answered on Mar 30, 2008


Sony Convergence
http://www.techlore.com/blog/entry/19694/Sony-Convergence-Repair-My-Sony-TV-has-a-distorted-picture-/
http://www.techlore.com/article/19631/Sony-Convergence-Procedure/

good luck
please mark the post with a fixya!

Sony KP-53S65... | Answered on Mar 17, 2008


You need new convergence ICs . They cost about 10.00 each you will need two. They are located on a large aluminum heat sink with an STK number stamped on them. They will have to be soldered in. If you can solder you will be able to do this repair yourself. Let me know if you need ay additional Info.

Sony KP-53S65... | Answered on Mar 14, 2008


Convergence ICs are bad it causes the red and/or blue to jump out of alignment making it look 3D. You have to convergence ICs located on a large aluminum heat sink with an STK number stamped on them. You can purchase new ones for about 10.00 each. they have to be soldered in. If you can solder you should easily be able to repair this yourself. Let me know if you need anything further.

Sony KP-53S65... | Answered on Feb 03, 2008


Replace the convergence ICs. They are located on a large aluminum heat sink with STK numbers stamped on them. They cost about 10.00 each. They have to be soldered in. Let me know if you need anything further.

Sony KP-53S65... | Answered on Jan 24, 2008


안녕하세요 제품설명 서를 불수가 있나요 한국어로 부탁합니다

Sony KP-53S65... | Answered on Jan 05, 2008


the screen control and the focus control on the flyback transformer need to be turned down a little

Sony KP-53S65... | Answered on Dec 31, 2007


Hi, you have a convergence problem, the IC`s and possibly a few precision resistors feeding the IC`s will have to be replaced, not an easy job if you haven`t done it before. If you are very proficient at solder work and can use a volt meter to check the resistors you can do the job but it isn`t easy for a lay-person, If you have more questions e-mail me back, good luck, BMW Rider

Sony KP-53S65... | Answered on Dec 31, 2007


i have a sound no picture

Sony KP-53S65... | Answered on Dec 18, 2007


Replace green CRT.....

Sony KP-53S65... | Answered on Oct 24, 2007


Replace green CRT....

Sony KP-53S65... | Answered on Oct 24, 2007


If the IC your talking about has a designation number of IC601, the number is MX0841AB-F. Common regulator IC. Sony says that IC is no longer avaialable. You may get lucky and take out the entire G board and have ptscorp.com, or Tristate.com repair the board for you. Good Luck

Sony KP-53S65... | Answered on Sep 18, 2007


By Phone Call 816-891-7550 By email inquiry:[email protected] Give model#

Sony KP-53S65... | Answered on Sep 07, 2007


it's called retrace lines ,your screens are set to high or focus block assy which has the screen adjustments on it also is faulty

Sony KP-53S65... | Answered on Aug 18, 2007


you need to replace the convergence ic'S inside the unit

Sony KP-53S65... | Answered on Aug 18, 2007


If the TV will not turn on and the red light blinks on the front of the set, it means that the microprocessor has detected a problem in the set and shut the set down. It then blinks the red light a certain number of times, and the number of blinks is the code for why the set has shut off. How many times does the red light blink before repeating?

Sony KP-53S65... | Answered on Aug 10, 2007


One of the Convergence IC's most likely shorted and that is the pop you heard. Is best to replace both and check micro fuses supplying + & - dc voltage to the chips. Also check the resistors in front of the IC's as they discolor or burn & change value.

Sony KP-53S65... | Answered on Jul 04, 2007


Not a problem Gayla, get on the NESDA web site and research a reputable shop from there.. http://www.nesda.com/locator/state_search.php It does sound like the convergence amps (IC's) are the fault. Could be that they have some poor solder connections and the ride in the truck excited the problem. In either event you probably want to have them replaced because if they've been arcing it's likely stressed the IC's close to failure. That unit takes the STK 392-150 but ask them to install the STK392-180 IC's instead. That will give you more reliability and greater tolerance to heat. And one more thing, Sanyo makes the STK line make sure you confirm with the shop to use ONLY Sanyo and not some Japanese knock-offs.

Sony KP-53S65... | Answered on Jul 02, 2007

Not finding what you are looking for?
Sony KP-53S65 53" Rear Projection Television Logo

130 questions posted

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76466 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Nasir Muhammad
Nasir Muhammad

Level 2 Expert

230 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sony Televison & Video

  • Sony Televison & Video

Most Popular Question

sony rear video projector kp 53s65

  • Televison & Video
Loading...