20 Most Recent Sony KP-57HW40 57" Rear Projection Television - Page 4 Questions & Answers


If the lamp light is blinking, then the lamp needs to be replace. If the Power/Standby light is blinking, then try resetting the TV. Turn Off the TV and remove the power plug from the wall outlet for 1 minute and reconnect it and check the operation. If the issue still persists, then the TV needs service.

Sony KP-57HW40... | Answered on Jul 26, 2010


Blue Picture Tube , bad Video IC on Blue CRT board.Or Blue screen drive control to tube needs to be adjusted down some.

Most Likely Bad Tube!

Sony KP-57HW40... | Answered on Jul 12, 2010


Ur tv have a problems known as a convergence problems,it dead.The tv convergence board,must require to change 2 STK convergence ICS and some or all it resistors to solved the convergence problems.U have soldering tools and matrials and know basic's solderings work?Tries websites like Tvrepairworld.com,Tvrepairkits.com to buy a convergence kit to do the repair it ur self.The shop will cost $300-350 for parts and labors.

Sony KP-57HW40... | Answered on Jul 10, 2010


your red picture tube bloomed, because of internal short. you might turn down screen control on red picture tube it might help. always mark with fingernail polish your starting position so you can always go back. J.D.W.

Sony KP-57HW40... | Answered on Jun 25, 2010


Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projeciton sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....
  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some photos of convergence problems.

42d3683.jpg

7859b01.jpg

e87380c.jpg
Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right. And you should be able to get the grid straight.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a fix

69189a5.pngCONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you are handy and can follow directions. You can get complete repair kits from TvRepairKits.com or click here. They have put together DIY repair kits that include the OEM parts and step by step photo instructions for each repair. If you are not handy or can't follow directions we would suggest calling a shop.

Sony KP-57HW40... | Answered on Jun 06, 2010


Projection sets have two very common problems.

The first common problem is convergence


These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. This is called convergence.

When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired. Convergence problems are very common on all Projection TV sets including Sony, Samsung,JVC,Philip Magnavox,Panasonic,Akai,Pioneer, Hitachi,Mitsubishi,Zenith and others.
You can get more information and a DIY convergenece repair kit with instructions from the link below.

Here are some of the most common problems with these sets...

*Screen Looks 3-D
*Colors wont align
*Screen may look distorted or warped
*No Audio/Video - TV Shuts down - May also make a constant chirping sound

Problem #2 - Another common problem is dull or washed out video.

Your set may have one or more of the following symptoms....

*Dull looking picture
*White looking picture
*Halos around objects
*Red/Orange looking picture

bb0cf99.pngYou can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Sony KP-57HW40... | Answered on May 30, 2010


Hi,

You can download the instruction manual in PDF format by clicking this link.
  • You'll require Adobe PDF Reader installed on your computer to view the manual. If it is not already installed on your computer, download it free from: http://get.adobe.com/reader/
Hope this solves your problem. Thanks for using FixYa.

Sony KP-57HW40... | Answered on May 20, 2010


well in texas you must have a sony authorised service center . please find one and take it there.ask a sony dealer and they will help you know where the service center is as the details is ussually on the warranty cards of the new items they sell.

Sony KP-57HW40... | Answered on May 20, 2010


this is a lamp issue try

www.discountmerchant.com over there you could see if the have the lamp if not you also can try discounttvlamps.com

regards

Sony KP-57HW40... | Answered on May 13, 2010


These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. This is called convergence.

When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired. Convergence problems are very common on all Projection TV sets including Sony, Samsung,JVC,Philip Magnavox,Panasonic,Akai,Pioneer, Hitachi,Mitsubishi,Zenith and others.
You can get more information and a DIY convergenece repair kit with instructions from the link below.

Here are some of the most common problems with these sets...

Problem #1) Convergence

Yours may have one or more of the following symptoms...

*Screen Looks 3-D
*Colors wont align
*Screen may look distorted or warped
*No Audio/Video - TV Shuts down - May also make a constant chirping sound

Problem #2 - Another common problem is dull or washed out video.

Your set may have one or more of the following symptoms....

*Dull looking picture
*White looking picture
*Halos around objects
*Red/Orange looking picture

bb0cf99.pngYou can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Sony KP-57HW40... | Answered on Apr 20, 2010


This sounds like a serious problem! Depending on your location i would call a certified technician to assess the situation in detail.
There are lots of components in devices like these, there could be a number of things wrong, and only a certified tech can find the best solution!



If this was helpful please rate with a 4 thumbs up!! Thanks for using fixya.com!!

Sony KP-57HW40... | Answered on Apr 17, 2010


Hi,
Symptom shows tv got problem with green picture tube that need to be replaced.
Rear projection tv has 3 picture tubes, red-green-blue to make color picture.
Since its an old model so spare parts would hardly be available and local tv repair shop will help you to arrange required part, if they can.
Thanks.

Sony KP-57HW40... | Answered on Apr 16, 2010


These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

Convergence problems are very common on all Projection TV sets including Sony,Samsung, JVC, Philip Magnavox, Panasonic, Akai, Pioneer, Hitachi, Zenith, and others. You can get a convergenece repair kit wiith instructions from the links below.

Here are some of the most common problems with these sets...

Problem #1) Convergence

Yours may have one or more of the following symptoms
  • Screen Looks 3-D
  • Colors wont align
  • Screen may look distorted or warped
  • No Audio/Video - makes a chirping sound.
Problem #2

Another common problem is dull or washed out video.
Your TV may have one or more of the following symptoms....
  • Dull looking picture
  • White looking picture
  • Halos around objects
  • Red/Orange looking picture

You can see some more examples and find a fix here
bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Sony KP-57HW40... | Answered on Apr 03, 2010


These sets have several common problems which are listed below.

Problem #1) Convergence

Yours may have one or more of the following symptoms
  • Screen Looks 3-D
  • Colors wont align
  • Screen may look distorted or warped
  • No Audio/Video - makes a chirping sound.
Problem #2

Another common problem is dull or washed out video.
Your TV may have one or more of the following symptoms....
  • Dull looking picture
  • White looking picture
  • Halos around objects
  • Red/Orange looking picture

You can see some more examples and find the fix here...

bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Sony KP-57HW40... | Answered on Apr 03, 2010


Projection TV sets have several common problems listed below.

Problem #1) Convergence

Symptoms:

  • Screen Looks 3-D
  • Colors wont align
  • Screen may look distorted
  • No Audio/Video - makes a chirping sound.
Example Photo:
5f6e85c.jpg
Problem #2 CRT Fluid has clouded over.

Symptoms


  • Dull Video, Washed out
  • White/Bright looking video
  • Halos around objects
  • Red/Orange looking
Example Photo:
ee1ca68.jpg

You can see more examples and find a fix here...

bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Sony KP-57HW40... | Answered on Mar 25, 2010


If you try to adjust convergence with the flash focus, perfect focus, (depending on the make of your set) or by manual convergence and the lines will not line up or even move. Your symptom sounds like a damaged convergence IC.

If you want to repair this set yourself, I have some instructions below that will be a help to you.
While it is not a very hard repair, this repair can be a bit tricky. If you have a 45W soldering iron, solder, solder wick, heat sink compound, and some basic soldering skills, you can repair the television yourself.
*** VERY IMPORTANT NOTE***
If your set is not producing a clear picture and the colors are not lining up, do not continue to watch the set as this can lead to further failure and possibly damage the individual CRT’s in the set.
I have repaired hundreds of these sets, so if you have any questions after reading the following, please reply to this post and I will help you in any way that I can.

With that aside I have some support suggestions that I have put together that may help you make an informed decision.

You should be able to get a local service center to repair this at your house for between $350.00 - $450.00, If you want to repair this set yourself, I have some instructions below that will be a help to you.
While it is not a very hard repair, this repair can be a bit tricky

How do I tell if the IC’s are damaged?
Since you cannot look inside of an IC, you will have to locate some of the components in the area around the convergence IC’s. You may be able to see some resistors that have changed colors or you test a resistor and it no longer reads the value marked by the color bands or the printed value. You will have to replace the IC’s and the supporting components.

When you remove the old IC's, please be sure to remove all of the old heat sink compound, as it can act as an insulator for the new IC's and cause them to overheat. I usually clean the heat sinks with alcohol and a small rag.


Where are the IC’s located and how do I find them?
There are two and large IC’s that control the convergence in a big screen set. Some of the newer sets only have one. If you only have one, it is right in the middle of the set on the center circuit board. They are secured to a very large aluminum heat sink. They will have a part number stamped on them that will start with an STKXXX-XXX, like STK392-110.

Along with the convergence IC’s there will also be some associated components that will need to be replaced as well. There are some resistors that are part of the convergence circuit that will be open and need to be replaced. Most likely these will appear charred in the center. If you have an Ohm Meter or a DVM, check all the resistors that are close to the IC’s and you should be looking for either ones that have opened or have changed values.

If one of the convergence IC’s are found to be bad, I would replace them both, if one has gone bad the other may go soon. I usually order my parts from Andrews Electronics in California, they will have the OEM components that you will need.
Their site is
http://www.andrewselectronics.com/welcome.aspx
And their phone number is a 24-Hour Order Desk: (800) 274-4666
I recommend the phone order so you can talk to the person about the different types of IC’s that are available.

I would also advise that the convergence IC’s be OEM or better, just because they are cheap does not mean that they are a good deal. I have seen the cheap IC’s fail after a short time, even though they look exactly like the OEM IC’s. I think that the bottom line is that you will get what you pay for when it comes to the parts.

You can also try
http://www.tvrepairkits.com/ , they do carry OEM or better parts. When you order from them you will get a kit with instructions on how to do the repair, step-by-step.



I hope this information allows you to resolve this issue.
If you need further assistance please comment to this post and I will try to help you further.
Thanks for using FixYa
asnowman


I have attached some photos of really bad convergence problems; your picture may not be exactly as bad as these.

de118e8.jpg

21efb26.jpg

Sony KP-57HW40... | Answered on Mar 15, 2010


Hi,
If your tv is Sony KP-57HW40 then its problem of convergence out chips failure and will be replaced. If tv is any other model, please mention it.
Let me know if you are handy with electronics stuff repair and can replace parts in circuit board with proper tools to provide you more technical details.
Thanks.

Sony KP-57HW40... | Answered on Mar 15, 2010


Blue tube is bad need to replace blue tube.. Tube no longer avail will need to be special ordered and my run from 350.00 up to replace part.

Sony KP-57HW40... | Answered on Mar 07, 2010


Projection TV sets have several common problems listed below.

Problem #1) Convergence

Symptoms:

  • Screen Looks 3D
  • Colors wont align
  • Screen may look distorted
  • No Audio/Video - TV makes a chirping sound.
Problem #2 CRT Fluid has clouded over. Symtoms
  • Dull looking video
  • White looking video
  • Halos around objects
  • Red/Orange looking video

You can see some examples and find a fix here...

bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Sony KP-57HW40... | Answered on Mar 06, 2010

Not finding what you are looking for?
Sony KP-57HW40 57" Rear Projection Television Logo

Popular Tags

271 questions posted

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76466 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Nasir Muhammad
Nasir Muhammad

Level 2 Expert

230 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sony Televison & Video

  • Sony Televison & Video

Most Popular Question

tv off but red light front flashing

  • Televison & Video
Loading...