Top 20 Sony KP-65WS510 65" Rear Projection HDTV-Ready Television Questions & Answers

0helpful
1answer

I just changed the flyback transformer on my sony kp-65ws510 tv but still blinking 8 times

Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://homenol.blogspot.com/ http://electronicshelponline.blogspot.com/ If blinks continue without any pause, the main board is faulty. Search the site by type in the "brand name" to your device, [Exclude the model number] in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.
8/20/2017 1:21:03 AM • Sony KP-65WS510... • 102 views • 0 helpful votes
0helpful
1answer

Convergence does not work. Black spot in corner of picture

Convergence will not cause the black spot--picture will look 3d or colors skewed, confirm model please and a clear idea of what set is doing or not.
10/14/2012 10:34:16 PM • Sony KP-65WS510... • 40 views • 0 helpful votes
0helpful
1answer

Possible Lamp Sensor Problem

Google the model number for six blinks for that is an error code---this set uses no lamp---it has 3 picture tubes
3/11/2012 10:34:48 PM • Sony KP-65WS510... • 115 views • 0 helpful votes
0helpful
1answer

My tv looks like 3d how do i fix on my own

install a convergence repair kit most models use the Sony convergence repair kit number 1 from www.tvrepairworld.com which has the parts and the CD with instructions.
10/20/2011 9:07:17 PM • Sony KP-65WS510... • 80 views • 0 helpful votes
0helpful
1answer

The left half of the

The tv have a problems known as a tv convergence pictures problems,it is dead.Tv set have any colors lines like R,G,B mis alingnments,have colors shadows pictures or a 3D pictures look alike?Yes,than the tv set convergence board it is dead to causes all these pictures problems.The tv set convergence board must have to be repair like replacing 2 STK convergence ICS and some or all of it resistors too.To fixed the tv set convergence board to solved the tv set covergence pictures problems.The tvs shops will cost u like $300-350 for parts and labors.
8/18/2011 3:56:08 PM • Sony KP-65WS510... • 239 views • 0 helpful votes
0helpful
1answer

I have a sony 65

Your model is a three CRT projection which doesnt have a thermal fuse. What are the symptoms of the set? Does the power indicator blink? If so how many times is it blinking?
5/21/2011 6:45:22 PM • Sony KP-65WS510... • 189 views • 0 helpful votes
0helpful
1answer

I TURNED MY TV ON

Projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Here are more details and solutions for both. Repair kits with instructions are also avail from www.TvRepairKits.com

Common Problem #1) Convergence has gone out

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some pics of convergence problems.


7859b01.jpg

e87380c.jpg
69189a5.pngSOLUTION #1

For more more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Common Problem #2) CRT Fluid is Cloudy

Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.

Picture of a set that needs the fluid changed.

578ba6c.jpg
TV set after fluid change

65af323.jpg

69189a5.pngSOLUTION

You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
1/29/2011 8:10:10 PM • Sony KP-65WS510... • 124 views • 0 helpful votes
0helpful
1answer

I have a sony kp65ws510

That's usually caused by the convergence ICs and associated pico fuses. You can get to repair kit called the Sony type I convergence repair kit from www.tvrepairworld.com the kit contains the parts and instructions on CD.
1/7/2011 4:43:11 PM • Sony KP-65WS510... • 223 views • 0 helpful votes
0helpful
1answer

The -20 volts is missing that goes to the conv.

Hi,
+/-22V come from G board by CN5004 pin4 and pin6 then enters in D board by CN8013 pin4 and pin6 and supplied to IC8001 and IC8002 (convergence output chips)
Reason of missing -20 volts could be D5002, L5008 and PS5001 on G board and above said connectors on G and D boards. Unplug connectors and replug back in to refresh connections.
Did you replaced convergence output chips in tv?
Let me know your findings to find out any further reason/ solution.
Thanks.
1/8/2011 11:12:15 PM • Sony KP-65WS510... • 203 views • 1 helpful votes
0helpful
1answer

On my Sony KP-65WS510 The colors are misaligned in

Hi,
This problem appears due to convergence output ICs failure located on D board in tv. There are two big black ICs that need to be replaced, soldering work is required.
Let me know are you handy with electronics stuff repair and can replace parts in circuit board to provide you more technical info OR local tv repairman will do this job for you.
Thanks.
11/23/2010 7:59:51 PM • Sony KP-65WS510... • 122 views • 0 helpful votes
0helpful
1answer

KP-65WS510 standby blinks 5 times then it shuts

This is a indication of high voltage regulation cuircit problem. specifically the cb board. This is a board sony recomends sending to them to get fixed and adjusted
10/20/2010 7:32:55 PM • Sony KP-65WS510... • 154 views • 0 helpful votes
0helpful
1answer

Heat sink bad redreciffier

Hi robert,
Welcome to FixYa.
My name is John. I will be assisting you with your issue.
Could you give me a little more information please?
12/27/2010 12:35:25 PM • Sony KP-65WS510... • 23 views • 0 helpful votes
0helpful
1answer

Misaligned convergence on sony kp-65ws510

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....
  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some photos of convergence problems.

42d3683.jpg

7859b01.jpg

e87380c.jpg
Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right. And you should be able to get the grid straight.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a fix

69189a5.pngCONVERGENCE SOLUTION

You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
8/8/2010 10:58:32 PM • Sony KP-65WS510... • 294 views • 0 helpful votes
0helpful
1answer

I have sony KP-65WS510 TV, started reporting

Tv have convergence problems first,fix the convergence board first.The tv have mis R,G,B colors lines alignment have 3D pictures effect.The tv convergence board have totoal dead 2 ICS convergence ICS and some or all it resistors.U know how to do basic's soldering?U have tools like a soldering iron,desoldering pump or solder witch and solders?Tries websites like Tvrepairworld.com,Tvrepairkits.com to buy ur tv make and model of convergence kit to repair it ur self.The shop will cost u $300-350 for parts and labors.Now,the projection lamp, might need to replaced too,after fixing the convergence problems.
8/27/2010 8:13:57 PM • Sony KP-65WS510... • 161 views • 1 helpful votes
0helpful
1answer

Sony KP-65WS510 projection tv blinks 6 times won't turn on

The 6 blink issue can be hard to diagnose with some serious testing / troubleshooting. The great majority of the time the culprit is the D board., and if not that then the G board. I would start with replacing the D board. There were a number of revisions for that board and to ensure you have the correct one you have to check the TV's serial number. The following is how they pan out:

Serial number starts with 80 then use D board part # A-1302-708-A.
Serial number starts with 87 then use D board part # A-1302-180-A.
Serial number starts with 90 then use D board part # A-1302-708-A.
Any other Serial number not starting with either 80 or 90 then use A-1302-180-A.

Now the bad news. The last time we had to go looking for this board 2 years ago it was extremely difficult to find a new board. I understand at this point many customers end up having to get the board rebuilt instead of replaced. You may have to talk to your local Sony shop to see how hard it is to get the board and if they know of any rebuilders in your area. There was a company online called PTS that was doing rebuilds. They have since been bought out or merged and the company name is now ModusLink. This is their website:

http://www.moduslink.com/Aftermarket_Solutions/index.cfm

You can contact them to see if they are still dong the rebuilds and what the cost is. Hopefully this will help get your TV going again.
4/18/2010 10:52:26 PM • Sony KP-65WS510... • 867 views • 0 helpful votes
0helpful
1answer

Sony kp-65w5510 rear projection tv power button malfuction

Replace bulb and clean cooling fans of dust is the first thing to do. if that doesnt work might start checking capacitors on the power supply.
5/10/2010 4:42:34 AM • Sony KP-65WS510... • 249 views • 0 helpful votes
0helpful
1answer

Convergence modules bad

Hi.

They are located on the D Board. Download the manual from the link below.

You can download the service manual here.
5/22/2010 12:00:35 AM • Sony KP-65WS510... • 111 views • 0 helpful votes
0helpful
1answer

When we turn the tv on your hear a buzz sound and

maybe your tv have a defect in power supply. just ask the Sony service center to fix your tv
6/19/2010 3:03:56 PM • Sony KP-65WS510... • 49 views • 0 helpful votes
0helpful
1answer

IHAVE A COVERGENCE PROBLEM WITH SONY KP-65WS510

Ur tv convergence are dead.U know how to solders?Must replaced 2 STK convergence ICS,and some or all it resistors.Tries websites Tv repair World.com,Tvrepairkits.com to buy a convergence kit to repair it ur self.The shop will cost u $300-350 for parts and labors.
4/1/2010 3:11:14 AM • Sony KP-65WS510... • 302 views • 0 helpful votes
0helpful
1answer

I need to replace the

Hi,

Please elaborate your problem providing us with more details and model number

Thanks for using FixYa.
5/29/2010 1:00:35 PM • Sony KP-65WS510... • 67 views • 0 helpful votes
Not finding what you are looking for?
Sony KP-65WS510 65" Rear Projection HDTV-Ready Television Logo

58 questions posted

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76713 Answers

Ekse

Level 3 Expert

13435 Answers

Nasir Muhammad
Nasir Muhammad

Level 2 Expert

233 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sony Televison & Video

  • Sony Televison & Video

Most Popular Question

20 volts missing goes conv

  • Televison & Video
Loading...