20 Most Recent
Sony Grand WEGA KDF-55WF655 36" Rear Projection HDTV - Page 2 Questions & Answers
Red light flashes 3 times
hold in on the power button for 10 sec make sure you put the cover on it good first if that dont work unplug it for a few sec then try to hold the power button down for 5- 10 sec that should work
Sony Wega kdf-55wf655 rear projection set keeps turning on and off
If picture quality is poor, be sure you aligned the bulb in the correct manner and be sure the cover for the bulb is not loose. Also, you might want to re check you picture setting as it might have gotten reset when you pulled the plug (I hope you pulled the plug when replacing the bulb).
Heres another solution (maybe temporary) to the problem of no picture and no sound for 30 seconds. I had my tv's power saving setting on "standard" before. After I switched it to "reduced", the problem was fixed. It has been almost two weeks without the problem. I think its a good fix until the new bulb comes in the mail.
Blue haze right down corner
Check it on a unused video input---if see reddish color area it is the optical light engine in the unit, a lot of this model had this issue--burn in optical engine lens.
Sony service bulletin
Hello,
You will get the Service Manual to your email by Pando.
Hope this will help.
Best regards,
Arpi
No remote sony wega
You can simpley fix this problem!Just buy a universal remote!BTW: Don't buy a new kind but on older kind of universal remote!It's just 10 bucks in a electric store!
Tv won't turn on red lights blinking
You are hearing the spark gap mounted on the lamp ballast board. If you can hear that sound, that means everything in the lamp driver circuit is working except the lamp!
Get a new lamp.
michtech
How do you change the bulb in a Sony KDF-55WF655
if you look right behind the fron grill on the sides of the set you will find two thumb screws, one on each side, you loosen these off and then the front grill comes off , you will have to use a little force on this, when you get the grill off in the middle of the set there is another thumb screw, this opens the lamp door. In the replacement lamp box there should be an allen wrench you use this to loosen the screws holding the lamp in, then you just pull the lamp out and replace it with the new one. Make sure the door is back in place and tightened down before attempting to turn this set on. No dlp set will operate with the door off.
Sony kdf46e2000
If the "bar" is black or darker than the rest of the screen it is a damaged optical light engine--caused by the intense heat from the lamp that shines into the engine.
KDF-E60A20 that has black screen
You either have a Ballast that is not firing the Lamp or you have a communication issue that is not telling the ballast to fire. You can confirm this by opening the lamp compartment and removing the lamp. Turn the set on and see if you are getting a blinking red led that flashes a error code. If you have this then you probably have a bad ballast.
If you don't have a error code flashing you probably have a bad Q-Box. It is a common source for communication issues. You can order it by part# A-1110-067-A through Sony via 1-800-222-Sony if needed. I'm sorry I do no have the part# for the ballast. Retail cost
is 471.50
Well, that is all I could come up with.
Hope it helps,
Skyassoc
5 blinks wont turn on
HelloThe main board of your Sony TV is faulty. Replacing the board is the only repair work, and no repair work to component to this board is possible. Before replacing the main board, a thorugh ckeck to the power board also is necessary, because, any voltage output from this board may cause troube to main board also. If you have knoledge in electronics, you can do the ork by yourself at home. If you have enough knoledge in electronics, and have confidence that you can do this work by yoursef, inform me. I've the repair document for your Tv, and I can help you to do this work, by send the manual to you, and assist you. OK
Not finding what you are looking for?