20 Most Recent
U-Line CO2075F-B Echelon Refrigerator Ice Maker Combination Questions & Answers
Ice maker freezes up
Icemaker Fill Tube Freezing
Make sure the water supply is greater than 20 psi. If too low, the water valve won't seat properly and it'll "weep." Common causes of low pressure are gunked-up saddle tap valves, kinked water supply line, and using a reverse osmosis filter to supply water to the icemaker.
Check to see if the black, flexible portion of the fill tube is wrinkled, twisted, or kinked which can cause ice dams that block the fill tube.
It turns out that the manufacturer's have been scratching their heads about this, too, and have concluded that the new fill tube air slit design helps prevent this problem.
Water supply to the ice
Hi
Over time the inlet valve becomes partially
plugged, reducing the outlet pressure and reducing the water flow rate into the
icemaker. If the flow rate is too low then the water will gradually freeze in
the tube until it becomes blocked entirely. Many times low water pressure will
cause this. You can perform a taste. Get a piece of tubing and attach it to the
inlet valve. Run this piece to a container and see if you get any water while
the power is off to the valve. You might have a valve that is not shutting
completely off. Hard water might cause this. Killing the power to the valve
will make the valve inoperable. Actually the purpose of killing the power is to
see if the valve is allowing water to bypass even when there is no signal from
the switch to do so.Bad inlet valve could be the possibility. So it needs to be
ordered and replaced because the valve isn't sealing off properly and it's
causing the water to trickle through or drip through the fill tube sometimes,
then it freezes before it reaches the icemaker and over time it will clog up
the fill tube completely.
Please get back to us if you have further query else please accept the
suggestion.
Thank you for contacting fixya.com
After having the ice maker
Sorry to hear about your problem. Sounds like you have a defrost issue. Hence your unit is not defrosting. All of this apply's if your freezer side has ice on it. If not. you have other issues, this does sound funny, but this is why your refrigerator side is warm, or not cooling.
Here is a list of some things that can go wrong.
1. Defective heat coil
2. Defective defrost timer
3. Defective defrost sensor
4. Defective Fan
5. Defective compartment inlet damper (on some models)
You should call a service company to resolve your issue.
Since I tried to help you, Please help me and Rate/Vote on the response. Thanks
Why does my U-line refrigerator keep frosting
Normal
0
MicrosoftInternetExplorer4
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";}
Hi,
Check out these tips...they can help you figure out whats going wrong with your
refrigerator and why it is not cooling
Refrigerator not Cooling or Fridge not Cooling
How to Defrost Refrigerator Defrost Timer Problem
Water Running in refrigerator from Freezer
heatman101
U-line UC02175 water inside pooling under veg
Well sounds like your ice maker evaporator drain hole is frozen, every time the unit goes into defrost cycle, water backs up and leaks down to the drawer. You can try turn off the refer for 48hrs with the doors open, most case it will reset by it self. If it is happening again in few weeks, then you evaporator drain pan heater is not working. Also make sure the doors are shut all the time.
Blinking light on 2075DWRRB
Thermistors are calibrated together with the board. When you order a board thermistors will come with them. When you get the board (display) a thermistor will be with it. You will have to pull unit out. remove the back panel and you will see the wires for the thermistor on your left and it plugs into the right side. That should help you. just remove permagum and pull the thermistor out. It just site in a tube.Part number for that model is 68005
U-line CO 2075 refrigerator stopped working, only
OK I'm guessing you have a clear icemaker. Not a co2075. When you replace the board you MUST replace the thermistors that come with the board. The board and thermistors are calibrated together. What is your model number? A clear ice maker has thermistors inside tubes. Except for the one on your filter dryer. Lets start with the correct model.
Open Thermistor on U-Line
It might be a bad thermistor. I would need the exact model number. It could be a open harness as well.
Not finding what you are looking for?