20 Most Recent Sony TA-N9000ES 5-Channel Amplifier Questions & Answers

0helpful
2answers

Hello! I have a problem

If the light blinks you need not check the fuse, its an indication that your amp has gone into protection mode due to an output failure. You will have to take it to an authorized service center because the S-master chip is a surface mounted device which needs a specialized equipment for de soldering and soldering.Even an ordinary service technician might refuse to handle this work.
5/26/2020 2:49:19 AM • Sony TA-N9000ES... • Answered on May 26, 2020
0helpful
2answers

No output.standby switch is blicking

R221 1ω was the problem.
12/5/2014 7:06:36 AM • Sony TA-N9000ES... • Answered on Dec 05, 2014
0helpful
1answer

Standby led blinking, no sound

Acording to the manual you have it in an invalid mode.
11/4/2014 8:11:27 PM • Sony TA-N9000ES... • Answered on Nov 04, 2014
0answers
0helpful
1answer

Hi, My S-Master 5.1 Digital Amplifier can't read

Most disc read errors are caused by dust or dirt on the lens of the DVD player. You should follow the cleaning instructions. Or watch a YouTube video on cleaning DVD lenses.
10/19/2013 3:12:52 PM • Sony TA-N9000ES... • Answered on Oct 19, 2013
0helpful
2answers

My Sony S-Master 5.1ch full digital amplifier is

When we turn on our 5.1ch Full Digital amplifier, it started smoking and sparks were flying. Can it be repaired
12/21/2012 10:54:57 PM • Sony TA-N9000ES... • Answered on Dec 21, 2012
0helpful
1answer

I have a Sony power

It's just a big amp with no controls you would change during normal operation. There's no remote. You don't name any source or if you even HAVE one attached. THAT would be a good place to look for missing sound.

Register and download the manual for free audio.manualsonline.com http://audio.manualsonline.com/manuals/mfg/sony/sony_ta_tan9000es.html http://dl.owneriq.net/f/fede44fb-b9ba-4e03-87bb-d0f3e29e22ef.pdf Set the BTL/Normal switch on the back to Normal. In fact, any switch or knob with BTL, set it to whatever choice is NOT BTL.

3/24/2011 1:36:35 PM • Sony TA-N9000ES... • Answered on Mar 24, 2011
0helpful
1answer

I am only receiving sound through two right side

maybe the wires are grounded.,., try to yurn the wires from left to right then reverse,.,,
12/28/2010 11:08:02 AM • Sony TA-N9000ES... • Answered on Dec 28, 2010
0helpful
1answer

My digital amplifier S-MASTER,mod HDC-SB300

hi,
may be ur amplifiers any of the output channel have some problem. that's why it goes off after power on, protecting ur speakers. disconnect all the speakers and inputs and then power on it if works check ur speakers and inputs. if not there is fault inside ur amplifier.
ok
12/22/2010 8:56:07 AM • Sony TA-N9000ES... • Answered on Dec 22, 2010
0helpful
1answer

When i start my super

Hi...
#1 Is the subwoofer connected? #2 Try connecting another speaker to see if your original sun is bad If the trouble is still there either you have a power supply failure or one amplifier section that has failed ( needs parts)
10/5/2010 11:34:38 AM • Sony TA-N9000ES... • Answered on Oct 05, 2010
0helpful
1answer

Our S-Master 5.1 ch full

to fix it you would need a soldering iron and some solder. Where is your location so I can set you up with a place to buy a new one?
9/4/2010 8:25:37 PM • Sony TA-N9000ES... • Answered on Sep 04, 2010
0helpful
1answer

Accidentally plug 110v dryer into

The dryer would have burned off the coils as the voltage is double of the operating voltage that was designed. ALl what can be done is to open and find out the break in the heater resisitor winding . These wires act a fuse and would have just burned out and lost the connection. find it out by a continuity test and connect at this point by joining , twisting. Now test the continuity and test on the 110 volt. it must work hope fully if the motor has not burnt out too. Hope you try. Good day..
7/31/2010 11:16:10 AM • Sony TA-N9000ES... • Answered on Jul 31, 2010
0helpful
1answer

I accidentally plugged my 110V amplifier to 220V

Hi and welcome to the site,

Initially, on a completely dead Sony TA-N9000ES, primary suspects to be checked would be:
  • 8A F1 fuse;
  • primary winding of T1 transformer;.
  • fusible resistors R816, R817 and R818.

Good luck and thank you for asking.
7/13/2010 2:27:07 PM • Sony TA-N9000ES... • Answered on Jul 13, 2010
0helpful
1answer

Sony TA-N9000ES Flash light when turn on.

an amp of this size generates alot of heat internally when in use as these use mosfet ICs and can get very hot.
your problem is most definately dry solder joints and possibly quite a few at that.
i've repaired quite a few sony surround receivers with similar problems and have all been down to dry solder joints.

hope this helps.
7/2/2010 11:22:34 PM • Sony TA-N9000ES... • Answered on Jul 02, 2010
0helpful
1answer

The word protect keeps coming up on the screen

This most likely is referring to a protection fault - ie a short circuit. Usually in the speaker wiring, it can also occur inside the unit.
4/2/2010 10:34:51 PM • Sony TA-N9000ES... • Answered on Apr 02, 2010
0helpful
1answer

Volume knob broken

needle nose pliers to turn it down,find another knob there pretty common even if you had to use a drop of super glue.
9/6/2009 5:29:43 AM • Sony TA-N9000ES... • Answered on Sep 06, 2009
Not finding what you are looking for?
Sony TA-N9000ES 5-Channel Amplifier Logo

31 questions posted

Ask a Question

Usually answered in minutes!

Top Sony Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5720 Answers

The Knight
The Knight

Level 3 Expert

76708 Answers

 Francisco Mauricio...
Francisco Mauricio...

Level 3 Expert

1551 Answers

Are you a Sony Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sony Audio Players & Recorders

  • Sony Audio Players & Recorders

Most Popular Question

sony s master 5 1ch full digital

  • Audio Players & Recorders
Loading...