Top 20 Sylvania 6427TE 27" TV Questions & Answers

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily. http://remotesearch.blogspot.com/ http://electro-medical.blogspot.com/ http://electronicshelponline.blogspot.com/ http://electrohelponline.blogspot.com/ Search the site by type in the brand name of your device, in the "Search box at the top right of the Home page display" to see the set-up codes to your device, with different brand remote controls. Programming Notes • If your device does not respond to the remote after trying all codes listed or your brand is not listed in the code list, use the Auto Code Search method to program your remote. • Sometimes the first code that "works" with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality. This is a trial and error procedure; and quiet time consuming. You might have to check different codes said for your device.

On older tv sets there are limited inputs...one for video and one for audio.. Find the white output hole for video on the back and run the cable to the set, and as for the audio there will be 2 red output holes (left and right on your dvd/vcr combo unit) this will use a special cable you can buy at radio shack that converts the left and right to just one output(it's like a "y" looking chord. it will still work if you just use one audio chord "out" from the dvd/,vcr unit but you will be hearing only one side of the "Stereo" plug these into the back of your old set the white is for video and the red is for audio.

Let the channel scan complete fully. This just needs to be done once for antenna channels and once if you use cable. Should take about 5 minutes to complete, but if u must interrupt or exit, press menu, or power to turn off TV. Make sure the tv's tuner setting is set appropriately for either cable or air (antenna), depending on your way of receiving channels, so it scans and finds properly.

Check the horizontal & vertical scanning section circuit. What else to do? If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Check the input selection settings to TV. Refer its user manual for details.

0601 0166 0460 0338. Try these codes. If you wish to get more; check the site linked here. It has set-up code list & set-up procedure to many popular brand remote controls. See it in "Mosaic" or "Magazine" view. It will make surf easier. http://electrohelponline.blogspot.com/ Try this link too http://remotesearch.blogspot.com/

The vertical scan output stage to this set has the fault. Check and replace damaged component/s at its vertical scan output circuit section. If you wish to get some details, check the site linked here. http://electronicshelponline.blogspot.com/ Pull up older posts. Check the site in 'Mosaic' view. It will make search easy.

Check the Main B+ voltage. If it is more than normal, this kind of fault can occur. To get some details, http://electronicshelponline.blogspot.com/ Pull up older posts.

I had one that did the same thing and it turned out to be the picture tube.

045,049,041. Check these codes. If you wish to get more details, check the sites linked here. Setup code list, and setup procedure to many popular brand remote controls are given. http://electrohelponline.blogspot.com/ http://remotesearch.blogspot.com/ Selecting the view option, either to Mosaic / Time slide, can be selected by the drop-down list, at the top left of the display window, will make surf easy.

possibly on you control panel. Were the password is unknown thus need to reset your system.

What help do you want?

one of the energy cables is damaged, so tv 'safety protcol' turns on, not to burn shuts off.go to service

You must have remote control to select inputs.

If you wish to get more details, check this site. Pull up older posts there. Check the site with patience, as it has over 2200 posts now. All are related to electronic equipment repair help.

Use the red and white cables for audio in and the yellow cable for the video in.

Yes, it is not possible to exit into any service mode without any remote. I've been almost 25 service mode entering and exiting on any brands since 2004 thus i said impossible to exit without a remote. Thanks for using Fixya.

Setup codes for Sylvania TV are: 0062 0004 0009 0135 0189 0183 0227 0456 0008 0068 0075 0141 0161